MGC ULTIMATE mini switch / HAT doesn't work together
Moderator: AdminGroup
- fallout9
- Posts: 5250
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 209 times
- Been thanked: 1230 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Try again with attached fm please, unzip first.
- Attachments
-
- _BlackBox_MK2_GF_MCG_Ultimate_Twist_v2_08_8.zip
- (73.45 KiB) Downloaded 98 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Hi,
didn't work, same as usual, in factory config, ministicks work, when I swap one of them for a HAT, they stop to work.
regards.
didn't work, same as usual, in factory config, ministicks work, when I swap one of them for a HAT, they stop to work.
regards.
Re: MGC ULTIMATE mini switch / HAT doesn't work together
I seem to be having the same problem. I switched out the top ministick for the "clicky" POV switch, for the love, I can't get the axis to work when the mode is switched.
The mode switches successfully, but the axes just don't work.
The mode switches successfully, but the axes just don't work.
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Hello,
for me lastest firmware didn't work too, look like an hardware issue.
Can we do ticket to the seller?
regards
for me lastest firmware didn't work too, look like an hardware issue.
Can we do ticket to the seller?
regards
- fallout9
- Posts: 5250
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 209 times
- Been thanked: 1230 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
This is very strange indeed. It's not hardware, because the ministicks still works in a different combination and it's also not software, because I have a MCGU right in front of me running properly on the latest software/firmware.
-
- Posts: 3290
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 45 times
- Been thanked: 639 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
When replacing the top mini-stick with a push-button module, you will no longer need uSSw on the central button - we do not have the 3rd and 4th axes. The ministik remained only on the 5th and 6th axes, but by default there is no uSSw switch on it, it needs to be configured. And in POVs also register that the axes/HAT work.
In such cases, I suggest attaching your profile (in zip) to clarify the location of the problem.
In such cases, I suggest attaching your profile (in zip) to clarify the location of the problem.
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Hi,
Sorry for delay, I wasn't at home.
So I join all profile pics in zip for the following config
hat in MASTER MODE, and ministick in GATE CONT (I just swap from factory setting with two ministick, all works fine).
Hat in master mode : center is 8 + 28-29-30-31 works.
ministick in gate cont : center is 32 and no axes work even default setting or re-calibrate.
Regards
Sorry for delay, I wasn't at home.
So I join all profile pics in zip for the following config
hat in MASTER MODE, and ministick in GATE CONT (I just swap from factory setting with two ministick, all works fine).
Hat in master mode : center is 8 + 28-29-30-31 works.
ministick in gate cont : center is 32 and no axes work even default setting or re-calibrate.
Regards
-
- Posts: 3290
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 45 times
- Been thanked: 639 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Your axes are not calibrated. And that's all.
It was not the screenshots that needed to be packed into the archive, but your profile, which was saved after calibration with the Save button.
It was not the screenshots that needed to be packed into the archive, but your profile, which was saved after calibration with the Save button.
Re: MGC ULTIMATE mini switch / HAT doesn't work together
ok, sorry for profile, here is the good file.
However, when I try to calibrate axes nothing happen for the ministick in GATE CONT, even if I program center in uSSw tempo.
regards
However, when I try to calibrate axes nothing happen for the ministick in GATE CONT, even if I program center in uSSw tempo.
regards
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Hi,
Is it normal than hat (in master mode position) make work the axis 3 and 4?
Regards.
Is it normal than hat (in master mode position) make work the axis 3 and 4?
Regards.
- fallout9
- Posts: 5250
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 209 times
- Been thanked: 1230 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Hello to all,
Problem has been solved, but it was an hardware issue, a ticket has been made, and product returned.
I received today my new grip,
now uHAT and uMSTICK work fine when installed.
Thanks to fallout9 for his help and time spent.
Best Regards.
asat
Problem has been solved, but it was an hardware issue, a ticket has been made, and product returned.
I received today my new grip,
now uHAT and uMSTICK work fine when installed.
Thanks to fallout9 for his help and time spent.
Best Regards.
asat
Who is online
Users browsing this forum: No registered users and 51 guests