Hi there,
been successfully trying out the latest firmware and software updates related to my GF MCG PRO setup. However, since 1_94B onwards (I think, and the associated VkDevCfg release) I have an error/bug that seems to be easy to re-produce:
1. Download _BlackBox_GF_MCG_v1_94_D.vkb and VKBDevCfg-C_v0.87.84.zip
2. Patch the box.
3. Set defaults and save.
4. Run axis calibration and save.
5. Enable A2B and all MCG Pro trigger axis buttons, and save. - Notice correct indication on test page after restart.
6. Enable Eq for main X and Y GF axis, set up response curves to your liking, and save.
7. Notice on restart that all MCG Pro trigger axis buttons are permanently on.
Hope this helps. The issue started with one of the recent updates. Think around beginning of July.
MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
Moderator: AdminGroup
-
- Posts: 3288
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 45 times
- Been thanked: 639 times
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
Show, please, a screenshot of the A2B tab for the trigger. And in the future, try to apply the appropriate screenshots (they should be done together with the Alt key). This will identify and solve the problem faster.
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
Screenshot from A2B config page (including GF X/Y response curves):
Test page showing Button 25, 26 and 28 permanently active (unable to activate button 27):
Note: Until GF X/Y response curve is set, the A2B buttons trigger as expected.
Test page showing Button 25, 26 and 28 permanently active (unable to activate button 27):
Note: Until GF X/Y response curve is set, the A2B buttons trigger as expected.
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
Tried again with the 1_94_F firmware from 13 August, no luck unfortunately.
Is there any expectation on when this might be addressed. Not a showstopper, although it limits some functionality.
Thanks in advance!
Edit: Also tried reverting to the firmware/software referenced here http://forum.vkb-sim.pro/viewtopic.php?f=25&t=3206 without luck.
Is there any expectation on when this might be addressed. Not a showstopper, although it limits some functionality.
Thanks in advance!
Edit: Also tried reverting to the firmware/software referenced here http://forum.vkb-sim.pro/viewtopic.php?f=25&t=3206 without luck.
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
To add,
I found this to be the X axis only and of the response curve for it, the 40% adjustment from 128 is at fault. All other adjustments seem to work fine.
I found this to be the X axis only and of the response curve for it, the 40% adjustment from 128 is at fault. All other adjustments seem to work fine.
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
Tested v1_95_2 (along with vkbdevcfg 0.88.45):
Some changes; The A2B buttons for the trigger are all on by default now (rather than previous off), but not reacting to any axis movement.
Edit: Referenced the wrong firmware version.
Some changes; The A2B buttons for the trigger are all on by default now (rather than previous off), but not reacting to any axis movement.
Edit: Referenced the wrong firmware version.
Last edited by CARTOK on Sun Sep 16, 2018 16:40, edited 1 time in total.
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
Apologies, I noticed now that I referenced the wrong firmware version. Fixed my previous post. To confirm, I tested the most recent firmware (1.95.2) and configurator (0.88.45).
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
CARTOK wrote:Tested v1_95_2 (along with vkbdevcfg 0.88.45):
Some changes; The A2B buttons for the trigger are all on by default now (rather than previous off), but not reacting to any axis movement.
Edit: Referenced the wrong firmware version.
This was the result. Not working.
Who is online
Users browsing this forum: Google [Bot] and 54 guests