The Y-axis has now started showing the same error today.
Severe Gunfighter MkII Axis Glitches
Moderator: AdminGroup
Re: Severe Gunfighter MkII Axis Glitches
Gunfighter MkII w/MCG-Pro
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
Re: Severe Gunfighter MkII Axis Glitches
This is interesting.
I experimented with re-calibrating and then unplugging the blackbox and then re-plugging.
BEFORE
AFTER:
Any thoughts, Gator? I don't know what to make of this because if I experience the issue, merely unplugging the blackbox and then re-plugging had no affect. The same goes for re-calibration alone...
This seems bizzare.
I experimented with re-calibrating and then unplugging the blackbox and then re-plugging.
BEFORE
AFTER:
Any thoughts, Gator? I don't know what to make of this because if I experience the issue, merely unplugging the blackbox and then re-plugging had no affect. The same goes for re-calibration alone...
This seems bizzare.
Gunfighter MkII w/MCG-Pro
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
Re: Severe Gunfighter MkII Axis Glitches
Apparently it was not a permanent solution.
Gunfighter MkII w/MCG-Pro
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
- rrohde
- Posts: 618
- Joined: Thu Oct 08, 2015 9:28
- Location: USA
- Has thanked: 681 times
- Been thanked: 242 times
Re: Severe Gunfighter MkII Axis Glitches
Hi,
Still waiting for you to open that support ticket at VKBcontrollers.com...
Still waiting for you to open that support ticket at VKBcontrollers.com...
VKB North America
https://VKBcontrollers.com
https://VKBcontrollers.com
Re: Severe Gunfighter MkII Axis Glitches
I had the exact same issue. Then, a wire sheared in the gunfighter base. I repaired it and the axis jump disappeared entirely.
Re: Severe Gunfighter MkII Axis Glitches
I received my new stick and base today and after getting everything connected and calibrated I am now getting a "Err-stat Active" message in VKBDevCfg and the brake lever's buttons are non-functional.
I can see the firmware is v1.936... so I thought my custom profile generated from v1.921 was the culprit. So I defaulted the profile, set the device, and yet the issue persists. Should I re flash the blackbox back too v1.921?
Any ideas?
I can see the firmware is v1.936... so I thought my custom profile generated from v1.921 was the culprit. So I defaulted the profile, set the device, and yet the issue persists. Should I re flash the blackbox back too v1.921?
Any ideas?
Gunfighter MkII w/MCG-Pro
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
Re: Severe Gunfighter MkII Axis Glitches
Update:
Re flashing the blackbox firmware back to v1.921 fixed the "Err_stat Active" message and I was able to get the brake lever's button I wanted to work by using the alternate method shown below.
Re flashing the blackbox firmware back to v1.921 fixed the "Err_stat Active" message and I was able to get the brake lever's button I wanted to work by using the alternate method shown below.
Gunfighter MkII w/MCG-Pro
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
Re: Severe Gunfighter MkII Axis Glitches
As for the original issue of X and Y axis signal drop out... it appears to be solved. Although I've only had the new stick for one day, I am not getting any signal drop out.
Gunfighter MkII w/MCG-Pro
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
Devconfig: v0.90.35
Gunfighter MkII w/Kosmosima Premium Left
Soft Cams X&Y
#10 Springs X&Y
FW: v1.976
T-Rudder Mk.IV Pedals
Soft Cam Side
High Spring Tension Setting
-
- Posts: 3288
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 45 times
- Been thanked: 639 times
Re: Severe Gunfighter MkII Axis Glitches
It is worth remembering a simple rule - a certain configurator will work correctly with the firmware, starting with a certain one, not lower, but higher. The topmost line in the configurator (cap) will speak eloquently about this.
I would like to see a screenshot of the physical axes tab to understand the logic of setting in the logical axes of the Precis parameter. At the last screenshot, did the stick move to the extreme positions along the X and Y axes?
I would like to see a screenshot of the physical axes tab to understand the logic of setting in the logical axes of the Precis parameter. At the last screenshot, did the stick move to the extreme positions along the X and Y axes?
Who is online
Users browsing this forum: Bing [Bot] and 45 guests