T-Rudder Mark III
1.67F Firmware
stock springs
stock cam
Hello my pedals have stopped working. They only show a value full right rudder in any software or game (no amount of pedal movement makes any difference)
They are fine mechanically, please assist,
Thank you
T-Rudder Mark III
Moderator: AdminGroup
Re: T-Rudder Mark III
I loaded the latest driver.
The rudder shows centered but no amount of pedal movement has an effect. I removed all the linkage and just connected the cable the board and spin the pot and nothing registers.
Are the electronics bad?
This should still be under warranty VKB, please assist. Where can I send this for repair?
Thanks.
The rudder shows centered but no amount of pedal movement has an effect. I removed all the linkage and just connected the cable the board and spin the pot and nothing registers.
Are the electronics bad?
This should still be under warranty VKB, please assist. Where can I send this for repair?
Thanks.
Re: T-Rudder Mark III
Thank you.
Only the green LED is lit, the yellow lights for a second if you disconnect and reconnect the USB cable or click on restart. Nothing changes if you disconnect or reconnect the RDR link cable.
Only the green LED is lit, the yellow lights for a second if you disconnect and reconnect the USB cable or click on restart. Nothing changes if you disconnect or reconnect the RDR link cable.
Re: T-Rudder Mark III
Hello any movement on this? How can I make a warranty claim and get this repaired?
-
- Posts: 3288
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 45 times
- Been thanked: 639 times
Re: T-Rudder Mark III
It is worthwhile to write additional lines to the file in Zconfig.ini, as it was advised here. After that, reset to the factory state the appeared button "Default", go to "Miscellaneous" in the Test and check the connection with the pedal Mars by clicking the green arrow. The green square should light up. Show screenshot. Screenshot do together with the Alt button.
Re: T-Rudder Mark III
This is where I am at. I am stuck I think the tiny box controller is ok but the actual pot and magnet and electronics
I just want to use my pedals. I think the problem lies here can I get the electrionic board on this photo.?
Asking a customer to go through all these hoops is not customer friendly.
I just want to use my pedals. I think the problem lies here can I get the electrionic board on this photo.?
Asking a customer to go through all these hoops is not customer friendly.
Re: T-Rudder Mark III
I will give that a shot ASAP. I bought some saitek pedals so I can continue flying at least.
Re: T-Rudder Mark III
This is my last attempt. There is no movement registered when I turn the pot. Can I send this in for repair?
- Attachments
-
- Fast Report Document.pdf
- (97.39 KiB) Downloaded 282 times
-
- Posts: 3288
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 45 times
- Been thanked: 639 times
Re: T-Rudder Mark III
Try to understand - to find out the reason, we need more information.
I asked for some simple actions to get it. But you do not want to do this. What is the reason?
Only after using all attempts to correct errors and recognize the inoperability of electronics, you can talk about the replacement.
So far, there is no such certainty.
Let's try again.
Add 2 lines (as in the screenshot) to the Zconfig.ini file. Be careful - one line in the [Common] section, the other in the [User] section.
Enter the configurator and click the appeared defaulte button.
Then go to the Test-> Miscellaneous tab and press the green arrow Mars.
The same box should light up.
Show a screenshot of these tabs.Thank you.
I asked for some simple actions to get it. But you do not want to do this. What is the reason?
Only after using all attempts to correct errors and recognize the inoperability of electronics, you can talk about the replacement.
So far, there is no such certainty.
Let's try again.
Add 2 lines (as in the screenshot) to the Zconfig.ini file. Be careful - one line in the [Common] section, the other in the [User] section.
Enter the configurator and click the appeared defaulte button.
Then go to the Test-> Miscellaneous tab and press the green arrow Mars.
The same box should light up.
Show a screenshot of these tabs.Thank you.
Re: T-Rudder Mark III
Its working again, I have no idea why other than I ran the very latest software did the button thing and screen shot. Then I checked the axes and the pot was working. So this thing was bricked up and now its not.
I put the pedals back and ended up with a larger washer, does that go on the potentiometer? Below the washer?
I put the pedals back and ended up with a larger washer, does that go on the potentiometer? Below the washer?
-
- Posts: 3288
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 45 times
- Been thanked: 639 times
Re: T-Rudder Mark III
To be honest - did not understand anything. Do the pedals work?
Also it is necessary to update the firmware for this configurator in order to avoid unforeseen problems.
Also it is necessary to update the firmware for this configurator in order to avoid unforeseen problems.
Who is online
Users browsing this forum: No registered users and 60 guests