How to setup Gunfighter MkII MCG Pro + T-Rudder Mk IV + Virtual Brakes
Moderator: AdminGroup
How to setup Gunfighter MkII MCG Pro + T-Rudder Mk IV + Virtual Brakes
This topic is clear viewtopic.php?f=27&t=2675 but not workings for my equipment configuration. Any suggestions?
-
- Posts: 3277
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: How to setup Gunfighter MkII MCG Pro + T-Rudder Mk IV + Virtual Brakes
If you show screenshots of your settings, then things will go much faster and more productively. Save your time and ours.
Re: How to setup Gunfighter MkII MCG Pro + T-Rudder Mk IV + Virtual Brakes
Sorry, it is impossible now, day after tomorrow will be. The config is default and the same, MCG Pro instead KG12 only.
If you don’t mind a couple of question before it will albe:
Should i apply exactly the http://ftp.vkb-sim.pro/Profiles/BlackBo ... _79_99.zip profile from previos post?
Which button is used for brakes activation in my MCG Pro?
If you don’t mind a couple of question before it will albe:
Should i apply exactly the http://ftp.vkb-sim.pro/Profiles/BlackBo ... _79_99.zip profile from previos post?
Which button is used for brakes activation in my MCG Pro?
-
- Posts: 3277
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: How to setup Gunfighter MkII MCG Pro + T-Rudder Mk IV + Virtual Brakes
You do not need to assign a brake button when changing the grip to the MCG.
She has a lever, which is much more convenient than a button. It is to this lever that virtual brakes are tied.
When changing the grip, the firmware must be changed and the previously made profile loaded (if it was configured and saved).
Not every airplane has separate brakes, there can only be a common lever. Therefore, there should be different profiles for such a case.
Check out this post, everything should be clear there.
She has a lever, which is much more convenient than a button. It is to this lever that virtual brakes are tied.
When changing the grip, the firmware must be changed and the previously made profile loaded (if it was configured and saved).
Not every airplane has separate brakes, there can only be a common lever. Therefore, there should be different profiles for such a case.
Check out this post, everything should be clear there.
Re: How to setup Gunfighter MkII MCG Pro + T-Rudder Mk IV + Virtual Brakes
Thanks a lot Ron61, will do and will report. It should be done
Re: How to setup Gunfighter MkII MCG Pro + T-Rudder Mk IV + Virtual Brakes
Some Actions report:
only Right Break works prorertly, when I press break lever (Axis Z) on stick and Right side of pedals the Slider 2 activates only. when I press break lever (Axis Z) on stick and Right side of pedals the Slider2 AND Slider1 activates simultaneosly
Pressing Left:
Pressing Right:
MY CONFIG Before:
Next After:
only Right Break works prorertly, when I press break lever (Axis Z) on stick and Right side of pedals the Slider 2 activates only. when I press break lever (Axis Z) on stick and Right side of pedals the Slider2 AND Slider1 activates simultaneosly
Pressing Left:
Pressing Right:
MY CONFIG Before:
Next After:
Last edited by Jj089 on Fri Feb 07, 2020 21:59, edited 1 time in total.
-
- Posts: 3277
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: How to setup Gunfighter MkII MCG Pro + T-Rudder Mk IV + Virtual Brakes
If it does not work or does not work as intended, then somewhere there is an error. It should be more attentive and then everything will turn out .
Re: How to setup Gunfighter MkII MCG Pro + T-Rudder Mk IV + Virtual Brakes
Thanks so much Ron!
My mistake
It’s perfect now, DCS Bf109 is alive again for me!
My mistake
It’s perfect now, DCS Bf109 is alive again for me!
Return to “Manuals and Howtos”
Who is online
Users browsing this forum: No registered users and 51 guests