Software MCGU + Gladiator Pro Mk2
Moderator: AdminGroup
-
- Posts: 16
- Joined: Mon Apr 30, 2018 17:24
- Has thanked: 9 times
- Been thanked: 1 time
Software MCGU + Gladiator Pro Mk2
Hello,
I just got my MCG Ultimate with twist in combination with my old Gladiator Pro Mk2, but stick is not recognized by software, and the red light blinks on Gladiator base. When i try to calibrate the white light on the stick flash once then no light at all. I had no problem setting up my old MCG twist stick.
What software package do i use for this combination?
I just got my MCG Ultimate with twist in combination with my old Gladiator Pro Mk2, but stick is not recognized by software, and the red light blinks on Gladiator base. When i try to calibrate the white light on the stick flash once then no light at all. I had no problem setting up my old MCG twist stick.
What software package do i use for this combination?
Last edited by Aviator001 on Sat Mar 11, 2023 12:55, edited 1 time in total.
Re: Software package MCGU + Gladiator Pro Mk2
The same. Up to date. What SW/FW versions do you use? Please show Global - External tab and Test - External devices.
Руководство пользователя по контроллерам VKB (VKB controllers User Guide) Ru&En
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
-
- Posts: 16
- Joined: Mon Apr 30, 2018 17:24
- Has thanked: 9 times
- Been thanked: 1 time
Re: Software package MCGU + Gladiator Pro Mk2
I used the links on the website. I deleted everything and started from scratch. now it says i use a very old version and need to update the firmware (software link from website) im confused about what software i need to use now..
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Software package MCGU + Gladiator Pro Mk2
Do this:
- download VKBDevCfg, zBootloader and the latest firmware package;
- unzip them in the same dedicated folder;
- close VKBDevCfg and run zBootloader as Admin;
- select your device on the bottom side of the window and click <Start Boot> button;
- when the device restarts in bootloading mode select it again, then press the <...> buton;
- navigate through the firmware folder to <Gladiator_series> folder and chose the file labeled <_Gladiator-K_MCG_Pro_v2_12_2.vkb>;
- after loading the file click the <Flash It!> button;
- when the flashing is over the zBootloader will close automatically;
- run VKBDevCfg as Admin, select this device at the top, then press the Default button under the Tools tab;
- after another restart calibrate it like here.
- download VKBDevCfg, zBootloader and the latest firmware package;
- unzip them in the same dedicated folder;
- close VKBDevCfg and run zBootloader as Admin;
- select your device on the bottom side of the window and click <Start Boot> button;
- when the device restarts in bootloading mode select it again, then press the <...> buton;
- navigate through the firmware folder to <Gladiator_series> folder and chose the file labeled <_Gladiator-K_MCG_Pro_v2_12_2.vkb>;
- after loading the file click the <Flash It!> button;
- when the flashing is over the zBootloader will close automatically;
- run VKBDevCfg as Admin, select this device at the top, then press the Default button under the Tools tab;
- after another restart calibrate it like here.
-
- Posts: 16
- Joined: Mon Apr 30, 2018 17:24
- Has thanked: 9 times
- Been thanked: 1 time
-
- Posts: 16
- Joined: Mon Apr 30, 2018 17:24
- Has thanked: 9 times
- Been thanked: 1 time
Re: Software package MCGU + Gladiator Pro Mk2
OK.. i got my old MCG stick on the base and followed the procedure and everything worked fine exept now the twist not working!?
Got the MCG Ultimate on the base and did it all over again and no connection to grib at all (red light flashing on base) only X Y axis on gladiator pro base works. When i connect the base to pc usb port, or right after calibration the white light on MCG stick flash once but no connection. Also cleaned connection surface on stick.
Uploaded some pictures of Device Config.
Got the MCG Ultimate on the base and did it all over again and no connection to grib at all (red light flashing on base) only X Y axis on gladiator pro base works. When i connect the base to pc usb port, or right after calibration the white light on MCG stick flash once but no connection. Also cleaned connection surface on stick.
Uploaded some pictures of Device Config.
Last edited by Aviator001 on Sat Mar 11, 2023 13:10, edited 3 times in total.
Re: Software package MCGU + Gladiator Pro Mk2
Softvare (vkbdevcfg.exe) Firmware. Grip not connected. Test - External devices. I sugggested it. Check connections.
Руководство пользователя по контроллерам VKB (VKB controllers User Guide) Ru&En
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
-
- Posts: 16
- Joined: Mon Apr 30, 2018 17:24
- Has thanked: 9 times
- Been thanked: 1 time
Re: Software package MCGU + Gladiator Pro Mk2
Victorus my old mcg grib worked fine, and i cleaned connection surfaces on new MCGU but grib is dead.I also pressed down on stick as i tighten the skrew. Could it be some bad connection or loose wire inside the grib or software problem?
When the white light is flashing on the grib there must be some kind of connection to the base.
When the white light is flashing on the grib there must be some kind of connection to the base.
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Software package MCGU + Gladiator Pro Mk2
What contacts do you have on top of the base, 3 pads or 3 pins?
-
- Posts: 3276
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: Software package MCGU + Gladiator Pro Mk2
Most likely, it's not about contacts - everything is fine with them. The firmware exists only for the MCG Pro grip (well, a very rare configuration), and both grips are distinguished by their unique bus address (pictured).
Therefore, it is not visible to the controller. But this is easy to fix if you select the correct MCGU grip in the drop-down list of devices and write it to the controller with the Set button. Then the connection will be restored and everything will work.
Therefore, it is not visible to the controller. But this is easy to fix if you select the correct MCGU grip in the drop-down list of devices and write it to the controller with the Set button. Then the connection will be restored and everything will work.
-
- Posts: 16
- Joined: Mon Apr 30, 2018 17:24
- Has thanked: 9 times
- Been thanked: 1 time
Re: Software package MCGU + Gladiator Pro Mk2
Thanks alot Ron61 it works fine now, but the RotZ axis is not responding at all. I recalibrated stick but no Twist.
My old MCG with twist also not working. I deleted everything and started all over so there must be something changed/reset in the Global-External or Profile-Axes setup right?
My old MCG with twist also not working. I deleted everything and started all over so there must be something changed/reset in the Global-External or Profile-Axes setup right?
-
- Posts: 3276
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: Software package MCGU + Gladiator Pro Mk2
If there are no connected pedals on the D-Mars sensor on the 7th axis, then we can declare the twist axis there. We make changes, calibrate - it should work.
-
- Posts: 16
- Joined: Mon Apr 30, 2018 17:24
- Has thanked: 9 times
- Been thanked: 1 time
Re: Software package MCGU + Gladiator Pro Mk2
Now it works thank you! i can see how it works now.
But there is a little misalignment on RotZ only when i turn left and back to center when i turn right and back to center it is pefectly in center.
The mechanical stop works fine so can it be something loose inside the grip like the magnet?
But there is a little misalignment on RotZ only when i turn left and back to center when i turn right and back to center it is pefectly in center.
The mechanical stop works fine so can it be something loose inside the grip like the magnet?
Last edited by Aviator001 on Sat Mar 11, 2023 12:21, edited 1 time in total.
-
- Posts: 3276
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: Software package MCGU + Gladiator Pro Mk2
Show the Profile-Axes tab.
Most likely, you need to increase the bit depth (Precis) to 11 and the dead zone in the center DzLo=10.
After writing to the controller, calibrate the axis and only then show the tab.
Most likely, you need to increase the bit depth (Precis) to 11 and the dead zone in the center DzLo=10.
After writing to the controller, calibrate the axis and only then show the tab.
-
- Posts: 16
- Joined: Mon Apr 30, 2018 17:24
- Has thanked: 9 times
- Been thanked: 1 time
Re: Software package MCGU + Gladiator Pro Mk2
Now everything works!
I changed Dz Lo to 7 and calibrated, this was enough to center Rot Z perfectly.
This is actually one awesome piece of software with a crazy amount of options.
Thank you for your help, very mutch appreciated.
I changed Dz Lo to 7 and calibrated, this was enough to center Rot Z perfectly.
This is actually one awesome piece of software with a crazy amount of options.
Thank you for your help, very mutch appreciated.
Who is online
Users browsing this forum: No registered users and 40 guests