Gladiator + THQ issue
Moderator: AdminGroup
-
- Posts: 11
- Joined: Fri Dec 24, 2021 11:39
Re: Gladiator + THQ issue
Tools tab > default button. Find&autoconfig. NXT XT v2.088 disappears from top box for about 5-10 seconds then reappears. And a bunch of "NXT Joker" tabs appear below. I start calibration and go to test tab on bottom. Go to Axes1 tab. Moving axes does not move silders.
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gladiator + THQ issue
Both screenshots you posted are taken after pressing the Default button. Now press the Find&AutoConfig button.
-
- Posts: 11
- Joined: Fri Dec 24, 2021 11:39
Re: Gladiator + THQ issue
still not working. by the way, I appreciate your help.
I can't send a video on this forum, so attached this is an imgur link showing exactly what I did
https://imgur.com/a/Rb7eqJd
I can't send a video on this forum, so attached this is an imgur link showing exactly what I did
https://imgur.com/a/Rb7eqJd
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gladiator + THQ issue
Seems like there's still an issue, the software doesn't run smooth at all. I suggest using another computer to finalize the setup.
-
- Posts: 11
- Joined: Fri Dec 24, 2021 11:39
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gladiator + THQ issue
Are you sure all the 4 pins on the main board are getting correctly into the socket on the GNX HID controller? What is the the position of the pins, did you altered it?
After checking these, try to restart your computer in safe mode and try again. Also, attached is an older firmware file, try it.
After checking these, try to restart your computer in safe mode and try again. Also, attached is an older firmware file, try it.
- Attachments
-
- _GNX_USB_Controller_v2.08.7.zip
- (75.01 KiB) Downloaded 77 times
-
- Posts: 11
- Joined: Fri Dec 24, 2021 11:39
Re: Gladiator + THQ issue
The older firmware file worked immediately! Unit was recognized as the correct device with the THQ name and all axes and buttons recognized in calibration. Thank you so much!
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gladiator + THQ issue
This is very strange. There is no other report about any module not working with the latest firmware.
But anyway, sorry it took so long until you could play with it, but glad it finally works; have fun!
But anyway, sorry it took so long until you could play with it, but glad it finally works; have fun!
-
- Posts: 11
- Joined: Fri Dec 24, 2021 11:39
Re: Gladiator + THQ issue
Yeah no idea. I got the GNX maybe a week ago. As soon as I tried the older firmware it immediately worked and the axes were recognized. It also immediately recognized it as a GNX and not with the prior name it had saw it as. I was using the same data file firmware I had been loading the entire time too.
Re: Gladiator + THQ issue
I have the same issue, I have the THQ module and it is not showing up in VKB Device config. I pluged it in into the VKB NXT GLadiator.... it is really frustrating at this point, there is no manual or guide included in the module.
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gladiator + THQ issue
What software and firmware versions are you on? If not sure, post a screenshot.
Who is online
Users browsing this forum: No registered users and 76 guests