I set up my THQ for dual engine. Calibrated with the VKB software but cannot make left and right engine to throttle similar. The right engine (axis y) always ahead and reach maximum be for left engine. The curve and everything else is at default.
Thanks
THQ: Dual Engine Throttle calibration.
Moderator: AdminGroup
- fallout9
- Posts: 5180
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: THQ: Dual Engine Throttle calibration.
Post a screenshot with Profile/Axes/Logical and Physical Axes. Don't crop the window please.
Re: THQ: Dual Engine Throttle calibration.
Thank for a quick response. Attach are the request screenshot. My setup is THQ connected with SEM and the HID is at SEM and axis x and y is physically link.
- fallout9
- Posts: 5180
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: THQ: Dual Engine Throttle calibration.
1. click the Default button under Tools tab;
2. click the Find&Autoconfig in the Global/External/External Devices panel;
3. calibrate.
2. click the Find&Autoconfig in the Global/External/External Devices panel;
3. calibrate.
Re: THQ: Dual Engine Throttle calibration.
Done all the step including unplug the usb and plug again. Still the same.
- fallout9
- Posts: 5180
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: THQ: Dual Engine Throttle calibration.
If you physically linked the 2 throttles with the white connector please remove it and do again the reset/find/calibrate.
Re: THQ: Dual Engine Throttle calibration.
Removed the link, recalibrated, reattached the link, remove and re-plug the usb. Still the same result. One observation that at about the same level, the axis X is behind while Y and Z are about the same. If I really would like to use it with twin now, I have to tie Y and Z instead of X and Y. But I don't want to do that.
Thanks,
Thanks,
- fallout9
- Posts: 5180
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: THQ: Dual Engine Throttle calibration.
First reset to default, then recalibrate without the link please. Post again the Physical and Logical Layers screenshots taken afterwards.
Re: THQ: Dual Engine Throttle calibration.
Hi,
Did the click the Default button, Start Calibr X Y Z individually, End Carlibr, remove and re-attach the usb. Same result. Y and Z Axis is the same level while X is behind. May be there is something wrong with the X axis sensor.
Did the click the Default button, Start Calibr X Y Z individually, End Carlibr, remove and re-attach the usb. Same result. Y and Z Axis is the same level while X is behind. May be there is something wrong with the X axis sensor.
- fallout9
- Posts: 5180
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: THQ: Dual Engine Throttle calibration.
Let's try this:
1. Change the axes number as below:
2. Check the En and Vs boxes for axes 4, 5 and 6 and press Set:
3. Recalibrate.
1. Change the axes number as below:
2. Check the En and Vs boxes for axes 4, 5 and 6 and press Set:
3. Recalibrate.
Re: THQ: Dual Engine Throttle calibration.
OK. Done Please see attached. There is something strange on the Device config app. There is always one row of tab at the bottom of the screen (Global, Profile, Macro, Test, Info) not below the main tab.
- fallout9
- Posts: 5180
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: THQ: Dual Engine Throttle calibration.
Please download this tester, maximize the tester on your screen and post 2 screenshots: one with moving up and down the 3 throttles and second one the same, but with the 2 throttles linked to each other.
Re: THQ: Dual Engine Throttle calibration.
Default, find and auto setting, calibrate and run the tester. One with each axis individually and the other one with axis x and y link.
- fallout9
- Posts: 5180
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: THQ: Dual Engine Throttle calibration.
The linked one is the first. Second is individual move. The forum took last photo selected first.
first pic. three strokes of linked x, y and three stroke of z
second pic. two strokes of each axis
first pic. three strokes of linked x, y and three stroke of z
second pic. two strokes of each axis
Who is online
Users browsing this forum: No registered users and 53 guests