Hello everybody,
I'm long time owner of gladiator with MGC pro system, also, I recently bought a GF 3 with ULTIMATE stick (twist version).
Devcfg-C version : v0.92.11
Bootloader version : v1.95
Firmware version : _blackbox_GF_MGC_Ultimate_Twist_v2_07_1
My problem :
When I swap one mini stick with one HAT, mini stick isn't recognize by system ( no axes, but center button work in "profile_button_physical layer", gate cont or master mode position).
I used all mini stick and HAT at different place (gate cont and master mode), used all existing procedure (from other topic, défaut button, flashing firmware, etc...) with no joy.
Blackbox MK2 blue light and center green light on.
Both mini stick works (two in place, POV function, axes, etc... ) when they are used at the same time.
Both HAT work too as previous configuration.
Does somebody have solution please?
Regards.
Asat84.
MGC ULTIMATE mini switch / HAT doesn't work together
Moderator: AdminGroup
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Sorry, but it's not clear what's working and what's not working. There are 2 types of modules: ministicks (the ones that comes installed from factory) and the HAT switches (the spares) - which ones are not working?
Re: MGC ULTIMATE mini switch / HAT doesn't work together
RE
Ok, my fault, sorry.
The essential :
When Ultimate is in configuration 1 Ministick + 1 HAT, ministick isn't recognise (flashing firmware, default setting, calibration, set loaded).
Following, screenshot in this configuration
Additional information :
When Ultimate is in factory config two ministicks work fine.
Regards.
Asat84.
Ok, my fault, sorry.
The essential :
When Ultimate is in configuration 1 Ministick + 1 HAT, ministick isn't recognise (flashing firmware, default setting, calibration, set loaded).
Following, screenshot in this configuration
Additional information :
When Ultimate is in factory config two ministicks work fine.
Regards.
Asat84.
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Please follow this guide from the timestamp. It's important to reset to default after swapping modules and calibrate. There's no Set or Load involved in this procedure, maybe this is what's messing up your profile. When it comes to calibration you will have to calibrate only the ministicks (the factory default modules), not the HAT switches.
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Hi,
Done, and no joy, when one HAT installed, ministick axes aren't recognised.
regards
Done, and no joy, when one HAT installed, ministick axes aren't recognised.
regards
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
How about ministick's POV stage? Is that working?
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Hi,
Negative, even with master mode function (red light on stick).
However, center button work, it will be see in profile/button/physical layer (poll check) when I press it.
Regards.
Negative, even with master mode function (red light on stick).
However, center button work, it will be see in profile/button/physical layer (poll check) when I press it.
Regards.
Last edited by asat84 on Mon Nov 15, 2021 12:25, edited 1 time in total.
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Alright, let's go step by step:
1. What module is installed on Gate Cont?
If ministick - does POV mode works, does axes mode works? Which cell lights up on Physical Layer chart when pressing the center push?
If HAT switch - do you get the 5 buttons all working in tester?
2. What module is installed on Master Mode?
If ministick - does POV mode works, does axes mode works? Which cell lights up on Physical Layer chart when pressing the center push?
If HAT switch - do you get the 5 buttons all working in tester?
1. What module is installed on Gate Cont?
If ministick - does POV mode works, does axes mode works? Which cell lights up on Physical Layer chart when pressing the center push?
If HAT switch - do you get the 5 buttons all working in tester?
2. What module is installed on Master Mode?
If ministick - does POV mode works, does axes mode works? Which cell lights up on Physical Layer chart when pressing the center push?
If HAT switch - do you get the 5 buttons all working in tester?
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Ok, let's go
1. What module is installed on Gate Cont?
_ ministick
_ does POV mode works : no
_ does axes mode works : no
Which cell lights up on Physical Layer chart when pressing the center push : #33
2. What module is installed on Master Mode?
_ HAT switch
_ do you get the 5 buttons all working in tester : yes (#22 center, #29 down, #30 left, #31 up, #32 right)
1. What module is installed on Gate Cont?
_ ministick
_ does POV mode works : no
_ does axes mode works : no
Which cell lights up on Physical Layer chart when pressing the center push : #33
2. What module is installed on Master Mode?
_ HAT switch
_ do you get the 5 buttons all working in tester : yes (#22 center, #29 down, #30 left, #31 up, #32 right)
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
1. In Global/Common set the #POV to 2;
2. In Profile/Buttons/Physical Layer click on the cell that lights up when you click on the center button of the ministick (you said #33, right?). In the new dialog box set it up as uSSw, then as POV2, then Switched by Tempo. If you want it to start in POV mode check the POV box; if you want axes mode by default, just leave it off. Photo1.
3. In Profile/POVs set the second POV as shown in Photo2. Hit Set to save and test the new settings.
2. In Profile/Buttons/Physical Layer click on the cell that lights up when you click on the center button of the ministick (you said #33, right?). In the new dialog box set it up as uSSw, then as POV2, then Switched by Tempo. If you want it to start in POV mode check the POV box; if you want axes mode by default, just leave it off. Photo1.
3. In Profile/POVs set the second POV as shown in Photo2. Hit Set to save and test the new settings.
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Hi,
No joy, I programmed as requested, 2nd POV is now available, however Tempo light still red, pressing center button didn't do anything, no axes recognize.
I tried to swap ministick and POV with the spare, but no joy too.
regards
Following screenshot.
No joy, I programmed as requested, 2nd POV is now available, however Tempo light still red, pressing center button didn't do anything, no axes recognize.
I tried to swap ministick and POV with the spare, but no joy too.
regards
Following screenshot.
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
1. Have you check the POV mode, does it work?
2. Center button is a long press to swap modes.
2. Center button is a long press to swap modes.
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Hi,
1. Have you check the POV mode, does it work?
Yes, nothing happen.
2. Center button is a long press to swap modes.
Yes, nothing happen.
I test to swap position, ministick in MASTER MODE and POV in GATE CONT. restore default setting (uSSw tempo in #34 position), and caliber.
_ red light turned on/off after long pressure on center button, but nothing else, no axes, no POV function.
I also tested the factory configuration, 2 ministicks, I set a second POV function as describe in your previous post, all works : 2 POV function, axes works, and both have a working tempo function on center long pressure to change mode (POV/axes).
after this test, I returned in the previous configuration (ministick in MASTER MODE and POV in GATE CONT), POV work, ministick stop to work (axes or POV function).
It look like I can't use a mixed configuration, just ministick + ministick or POV +POV.
Regards.
1. Have you check the POV mode, does it work?
Yes, nothing happen.
2. Center button is a long press to swap modes.
Yes, nothing happen.
I test to swap position, ministick in MASTER MODE and POV in GATE CONT. restore default setting (uSSw tempo in #34 position), and caliber.
_ red light turned on/off after long pressure on center button, but nothing else, no axes, no POV function.
I also tested the factory configuration, 2 ministicks, I set a second POV function as describe in your previous post, all works : 2 POV function, axes works, and both have a working tempo function on center long pressure to change mode (POV/axes).
after this test, I returned in the previous configuration (ministick in MASTER MODE and POV in GATE CONT), POV work, ministick stop to work (axes or POV function).
It look like I can't use a mixed configuration, just ministick + ministick or POV +POV.
Regards.
- fallout9
- Posts: 5182
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: MGC ULTIMATE mini switch / HAT doesn't work together
There's a fresh new firmware (and matching software) uploaded, please flash, reset to default, calibrate and get through all these tests again. It has to work, seems like all modules are fine and the grip's main board works good too.
Re: MGC ULTIMATE mini switch / HAT doesn't work together
Hi,
Same issue as usual, work in factory config, and ministick cease to work when POV is installed.
regards
Same issue as usual, work in factory config, and ministick cease to work when POV is installed.
regards
Who is online
Users browsing this forum: No registered users and 52 guests