Gladiator NXT calibration issues
Moderator: AdminGroup
-
- Posts: 7
- Joined: Thu Oct 07, 2021 17:14
- Has thanked: 1 time
Gladiator NXT calibration issues
1 -VKB-Sim Gladiator NXT R Pro Version
2 - v2.010
3 -Default ones (medium)
4 - Default
5 -0.92.06
6 - see attachement
7 - see attachement
Hello, I just bought and calibrated a Gladiator NXT Premium.
I followed the calibration guide and video several times, and the buttons flash as expected, but every time i check the Y axis, it does not go all the way down, but it stops at about 70% (see screeenshot).
Any way to solve this?
Product Name:
PRO version
T-Link supported
Firmware version:
2 - v2.010
3 -Default ones (medium)
4 - Default
5 -0.92.06
6 - see attachement
7 - see attachement
Hello, I just bought and calibrated a Gladiator NXT Premium.
I followed the calibration guide and video several times, and the buttons flash as expected, but every time i check the Y axis, it does not go all the way down, but it stops at about 70% (see screeenshot).
Any way to solve this?
Product Name:
PRO version
T-Link supported
Firmware version:
- fallout9
- Posts: 5184
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gladiator NXT calibration issues
Could be that the magnet on Y sensor got dislodged/unglued. Would worth to open it up and check it, and if that's the case, reglue it.
Please let me know if you need further assistance on this.
Please let me know if you need further assistance on this.
-
- Posts: 7
- Joined: Thu Oct 07, 2021 17:14
- Has thanked: 1 time
Re: Gladiator NXT calibration issues
Hi, I followed the guide here viewtopic.php?f=25&t=5508#p48532 and indeed the magnet came out as soon as I placed another magnet on it (see figure attached).
I added some new glue (cyanoacrilate based) and reaseembled it, then re-calibrated but now the issue seems much worse (see figure) and affecting both negative and positive movement. Does the magnet need to be oriented in a specific way?
I added some new glue (cyanoacrilate based) and reaseembled it, then re-calibrated but now the issue seems much worse (see figure) and affecting both negative and positive movement. Does the magnet need to be oriented in a specific way?
-
- Posts: 7
- Joined: Thu Oct 07, 2021 17:14
- Has thanked: 1 time
Re: Gladiator NXT calibration issues
here it is (btw I updated/downgraded the firmware too while I was waiting for a reply, so now I have a 2.071. Changing the firmware had no effect whatsoever. )
-
- Posts: 3277
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: Gladiator NXT calibration issues
No axis has been calibrated. Do not open the Test tab, we will calibrate from this one.
Press Tools, select all axes in the window, move each axis along the full range, press End.
We show the screenshot.
Press Tools, select all axes in the window, move each axis along the full range, press End.
We show the screenshot.
-
- Posts: 7
- Joined: Thu Oct 07, 2021 17:14
- Has thanked: 1 time
Re: Gladiator NXT calibration issues
Yes, it was not calibrated because you asked me to reset to default. Here it is after the calibration I performed: https://www.youtube.com/watch?v=P-uFAVYoQTw at the end one can see that the Y axis basically dos not work properly.
I also attached the result after the calibration.
I also attached the result after the calibration.
-
- Posts: 3277
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: Gladiator NXT calibration issues
Once again, there is no need to change or configure anything. Just reset to default with the button in the configurator and then calibrate according to the above method.
-
- Posts: 7
- Joined: Thu Oct 07, 2021 17:14
- Has thanked: 1 time
Re: Gladiator NXT calibration issues
Sorry but that's what I did the first 10 times I calibrated it. I just checked the two unchecked boxes in the last attempt (the one filmed) since you wrote to "select all axes in the window". The results were the same.
-
- Posts: 3277
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: Gladiator NXT calibration issues
In the Settings tab, activate the Partial Calibrations checkbox and from the pop-up window select only the 2nd axis you need for calibration.
When moving the handle, hold it a little in the extreme positions.
When moving the handle, hold it a little in the extreme positions.
-
- Posts: 7
- Joined: Thu Oct 07, 2021 17:14
- Has thanked: 1 time
Re: Gladiator NXT calibration issues
Did a partial calibration --> Same result https://youtu.be/xtV61eY8jsI
Checked cable and sensor (https://photos.app.goo.gl/CW4yoNUqN272rkrD9) , no evident damage, behaviour still the same after reassembling and recalibrated. Maybe the sensor is defective and worked better when the magnet was rotated in the previous position?
Checked cable and sensor (https://photos.app.goo.gl/CW4yoNUqN272rkrD9) , no evident damage, behaviour still the same after reassembling and recalibrated. Maybe the sensor is defective and worked better when the magnet was rotated in the previous position?
-
- Posts: 3277
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: Gladiator NXT calibration issues
Change the conductors in the connector according to the picture.
It should be - green, white, red, black. Only on the connector on the controller side, do not change on the sensor.
It should be - green, white, red, black. Only on the connector on the controller side, do not change on the sensor.
-
- Posts: 7
- Joined: Thu Oct 07, 2021 17:14
- Has thanked: 1 time
Re: Gladiator NXT calibration issues
Omg it worked! I was somewhat able to swap them without destroying the connector and after a calibration now works! (see attachments )
Who is online
Users browsing this forum: No registered users and 132 guests