How do I configure the Gunfighter Pro Mk. III grip/base with MCG Twist Adapter
Posted: Wed Aug 05, 2020 19:17
1 - Device model and version
Gunfighter Pro Mk. III grip/base with MCG Twist Adapter
2 - Controller Firmware version
Sorry, no idea
3 - Number and type of springs used
Not changed, so whatever came as standard
4 - Тype of cams used
Not changed, so whatever came as standard
5 - If VKB original software is used, please always mention its version
Not changed, so whatever came as standard
6 - Vkbjoytester screenshots. Download it here: http://ftp.vkb-sim.pro/Programms/VKB_JoyTester.zip
Not relevant to my request for help
7 - Vkbdevcfg-c screenshots. Download it here: http://ftp.vkb-sim.pro/Programms/; make sure you're downloading the newest version.
Not relevant to my request for help
As you can no doubt tell from the above, I am a complete novice where advanced jopysticks are concerned.
Eight weeks ago I purchase the Gunfighter Pro Mk. III grip/base and the MCG Twist Adapter, to replace a Thrustmaster T.16000M which is wearing out after only a few months use.
Having eventually managed to figure out how to put the Gunfighter joystick and adapter together (thank you video makers!), I have spent the time since then trying to figure out how to configure it.
I have downloaded the latest configuration software (VKB Device Config v0.91.12) and the user manual (controller_2_11_En.pdf). However, I can't find anywhere in the manual where it explains how to set up the Twist Grip adapter. The only information that I can find is on the store page for the adapter, where it says
· Re-configure the BlackBox (easy – just check two boxes in VKBdevCfg)
· Re-calibrate your Gunfighter w/ MCG including the newly added Z-axis
Unfortunately it doesn’t tell me which two boxes I should check, and as a novice at setting up advanced joysticks I can’t see any boxes in the Configurator that obviously relate to the adapter.
I submitted a support ticket but I have had no response, so I am hoping someone here can help me. Can someone please tell me which configurator boxes I need to check, or what else I need to do, so that I can configure the twist adapter and actually start to use it?
Thank you.
Gunfighter Pro Mk. III grip/base with MCG Twist Adapter
2 - Controller Firmware version
Sorry, no idea
3 - Number and type of springs used
Not changed, so whatever came as standard
4 - Тype of cams used
Not changed, so whatever came as standard
5 - If VKB original software is used, please always mention its version
Not changed, so whatever came as standard
6 - Vkbjoytester screenshots. Download it here: http://ftp.vkb-sim.pro/Programms/VKB_JoyTester.zip
Not relevant to my request for help
7 - Vkbdevcfg-c screenshots. Download it here: http://ftp.vkb-sim.pro/Programms/; make sure you're downloading the newest version.
Not relevant to my request for help
As you can no doubt tell from the above, I am a complete novice where advanced jopysticks are concerned.
Eight weeks ago I purchase the Gunfighter Pro Mk. III grip/base and the MCG Twist Adapter, to replace a Thrustmaster T.16000M which is wearing out after only a few months use.
Having eventually managed to figure out how to put the Gunfighter joystick and adapter together (thank you video makers!), I have spent the time since then trying to figure out how to configure it.
I have downloaded the latest configuration software (VKB Device Config v0.91.12) and the user manual (controller_2_11_En.pdf). However, I can't find anywhere in the manual where it explains how to set up the Twist Grip adapter. The only information that I can find is on the store page for the adapter, where it says
· Re-configure the BlackBox (easy – just check two boxes in VKBdevCfg)
· Re-calibrate your Gunfighter w/ MCG including the newly added Z-axis
Unfortunately it doesn’t tell me which two boxes I should check, and as a novice at setting up advanced joysticks I can’t see any boxes in the Configurator that obviously relate to the adapter.
I submitted a support ticket but I have had no response, so I am hoping someone here can help me. Can someone please tell me which configurator boxes I need to check, or what else I need to do, so that I can configure the twist adapter and actually start to use it?
Thank you.