Hello
today I was in DCS and suddenly the plane startet to roll to the right like hell and didn't stop. After a reset, it was flying straight again but I couldn't turn to the left, only very very slightly. Thereafter I looked in to my VKB def and found the following. I already did a new calibration, I pressed the defauld button and then a new calibration and also removed the cable from the x axis and have put it back on. Any idea or help would be much appreciated.
Attached you'll find three pictures of the Vkb Dev. I have also three pictures from the JoyTester but I couldn't upload these ones as the server just allows an upload of three items.
I am using the following:
Gunfighter Mk II MCG Pro Englisch v. 1.986
NJoy32 firmware v.1.98.5
VKBdev v.0.91.10
Thank you for your help in advance
Gunfigher Mk II MCG Pro Eng X Axis broken
Moderator: AdminGroup
- fallout9
- Posts: 5184
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gunfigher Mk II MCG Pro Eng X Axis broken
Post screenshot with Profile/ Axes/ Physical axes tab please.
- fallout9
- Posts: 5184
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gunfigher Mk II MCG Pro Eng X Axis broken
Which axis are you using for roll? Do you have a twist module on your MCG Pro?
Re: Gunfigher Mk II MCG Pro Eng X Axis broken
according to the TEST page I'm using the Axis X for roll movement and I have not a twist module installed. I'm having the 200mm extension installed and I'm using one 50 and one 20 spring per axis.
- fallout9
- Posts: 5184
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gunfigher Mk II MCG Pro Eng X Axis broken
The X axis is totally uncalibrated in your screenshot, try to calibrate it again.
Re: Gunfigher Mk II MCG Pro Eng X Axis broken
done but I can't calibrate it as it should be because I don't get the full travel of the x-axis....see screenshot below which I took during calibration. The upper picture is full left physical detend and the lower one full right physical detend
- fallout9
- Posts: 5184
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gunfigher Mk II MCG Pro Eng X Axis broken
No sir, I swapped the soft center to the hard center cams immediately upon arrival of the stick and as well as the springs. Thereafter I never touched anything again apart from the grip while flying.
- fallout9
- Posts: 5184
- Joined: Wed Oct 03, 2018 20:37
- Has thanked: 208 times
- Been thanked: 1218 times
Re: Gunfigher Mk II MCG Pro Eng X Axis broken
Can you open the base at the bottom and post a picture?
Re: Gunfigher Mk II MCG Pro Eng X Axis broken
sure! there you go
Top one is with the blackbox cable connected, the other two are without blackbox cable.
Top one is with the blackbox cable connected, the other two are without blackbox cable.
Re: Gunfigher Mk II MCG Pro Eng X Axis broken
I've reconnected it but I still can't calibrate it right as everything remains as it is......full right physical movement does not go full right within the vkd dev and full left still gives just a little movement also to the right.
Who is online
Users browsing this forum: No registered users and 49 guests