GF2->3 and Twist install questions
Posted: Sun Dec 29, 2019 4:06
Hey Guys,
Need some advice on the following:
1. When doing the GF II -> 3 upgrade on an early model MCGPro grip - what should be done with the dry-clutch lock-nut? I use the spare washers (normal and split) behind the PCB and then re-installed the lock-nut on-top... Its only just hanging on there (maybe 1/2 thread) - and I don't even think it really needs the lock-nut - can you confirm? If I don't use washers there is about 1mm gap between dry-clutch and PCB...
2. What are the "A" springs for? They seem longer than the supplied #10 spring?
3. What does the red-dot on the #20A spring package signify?
4. What firmware should we be using is the _BlackBox_MK2_GF_MCG_PRO_v1_98_1.vkb the correct one? (Not sure now that its a GF MK3).
5. The Twist adapter only came with a single hex bolt, on the early MCG-Pro grips there are black screws (well screw head, but bolt) - was the intention to replace one of these screws with the hex bolt? Why wasn't two bolts supplied? Or did I miss something?
6. I assume its ok to reuse the old springs with the new cams? They did seem to stretch quite a lot more (I am using Space-S cam if that matters)
Some notes:
1. The soft spring on the twist adapter is far better, its not only easier to twist, but not too easy...but it reduces the creak noise from the casing when twisting...
2. The procedure for removing cams should be updated to highlight undoing the NUT end, rather than the hex-bolt end - I started to round out the hex bolt because I was stupid...
3. There is a bit of "slop" noise from the dust cover when moving the stick; I assume its the dust-cover binding on itself? not a big deal, but thought I would mention it..
4. I really like the new cams, they seems smoother!
All-in-all I am pretty happy, thanks and well-done on some excellent engineering!
Regards
D.
Need some advice on the following:
1. When doing the GF II -> 3 upgrade on an early model MCGPro grip - what should be done with the dry-clutch lock-nut? I use the spare washers (normal and split) behind the PCB and then re-installed the lock-nut on-top... Its only just hanging on there (maybe 1/2 thread) - and I don't even think it really needs the lock-nut - can you confirm? If I don't use washers there is about 1mm gap between dry-clutch and PCB...
2. What are the "A" springs for? They seem longer than the supplied #10 spring?
3. What does the red-dot on the #20A spring package signify?
4. What firmware should we be using is the _BlackBox_MK2_GF_MCG_PRO_v1_98_1.vkb the correct one? (Not sure now that its a GF MK3).
5. The Twist adapter only came with a single hex bolt, on the early MCG-Pro grips there are black screws (well screw head, but bolt) - was the intention to replace one of these screws with the hex bolt? Why wasn't two bolts supplied? Or did I miss something?
6. I assume its ok to reuse the old springs with the new cams? They did seem to stretch quite a lot more (I am using Space-S cam if that matters)
Some notes:
1. The soft spring on the twist adapter is far better, its not only easier to twist, but not too easy...but it reduces the creak noise from the casing when twisting...
2. The procedure for removing cams should be updated to highlight undoing the NUT end, rather than the hex-bolt end - I started to round out the hex bolt because I was stupid...
3. There is a bit of "slop" noise from the dust cover when moving the stick; I assume its the dust-cover binding on itself? not a big deal, but thought I would mention it..
4. I really like the new cams, they seems smoother!
All-in-all I am pretty happy, thanks and well-done on some excellent engineering!
Regards
D.