Black box still flashing after attaching MCG to my Gunfighter Pro Rev A. I have run the VKB device config also. Black box shows as if I did not have a grip attached.
What am I doing that is incorrect?
Black box still flashing after attaching MCG to Gunfighter
Moderator: AdminGroup
Re: Black box still flashing after attaching MCG to Gunfighter
DO I have to flash the firmware so it can see the MCG? If so, Z-Bootloader does not see my device. I read that I maybe have to short Boot jumpers on my device. I have taken it apart to look for such a jumper, but I do not see one. Is it on the Black box?
Re: Black box still flashing after attaching MCG to Gunfighter
!!! http://forum.vkb-sim.pro/viewtopic.php?f=25&t=2762
Please show screenshots of VKBdevcfg.exe.
1. What devices does it see if you connect GF base?
2. With attached MCG?
If any.
Please show screenshots of VKBdevcfg.exe.
1. What devices does it see if you connect GF base?
2. With attached MCG?
If any.
Руководство пользователя по контроллерам VKB (VKB controllers User Guide) Ru&En
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
Re: Black box still flashing after attaching MCG to Gunfighter
Sorted it. I found this article.... https://vkbcontrollers.com/?p=8185
I have green lights and am good to go and blow stuff up now
I have green lights and am good to go and blow stuff up now
Re: Black box still flashing after attaching MCG to Gunfighter
Gunfighter pro RevA. MCG Pro RevA
Firmware Version: 1.94.B
Now Windows shows me a message saying the device has malfuctioned. Windows is no longer detecting my Gnufighter
Firmware Version: 1.94.B
Now Windows shows me a message saying the device has malfuctioned. Windows is no longer detecting my Gnufighter
Re: Black box still flashing after attaching MCG to Gunfighter
What happens if you connect GF base only? Without any grip?
Руководство пользователя по контроллерам VKB (VKB controllers User Guide) Ru&En
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
-
- Posts: 313
- Joined: Sun Oct 01, 2017 5:00
- Location: Representin' the 302
- Has thanked: 20 times
- Been thanked: 86 times
Re: Black box still flashing after attaching MCG to Gunfighter
Maybe worth looking at and easy enough to check. Open up the bottom of the base and check the wires between the 4-pin connector and the circuit board. Try taking the connectors apart and re-seating them. Don't pull them by the wires! Could be just another case of a loose connector inside the base causing gremlins. This has happened, but it's usually happened to the gimbal connectors when it does. Just a thought. Of course, it could be the USB cable, but I'd give that a shot before writing it off.
Gunfighter MkI w/MkIII update + MCG-Pro Grip
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Re: Black box still flashing after attaching MCG to Gunfighter
Andy wrote:got to figure out how to set all the buttons up in DCS.
It might be a bit tiring, but it does pay in long term. Good luck!
Best Regards,
AeroGator
AeroGator
Re: Black box still flashing after attaching MCG to Gunfighter
Andy wrote:It is the USB cable to the black box. It works now, I just got to figure out how to set all the buttons up in DCS.
Hurray!!!
What problem with button mapping?
Руководство пользователя по контроллерам VKB (VKB controllers User Guide) Ru&En
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
Re: Black box still flashing after attaching MCG to Gunfighter
I don't know how to do this. When I try setting master mode as buttons, it usually mashes several buttons together, so i guess I need to set deadlines or something. A guide would be really useful.
Re: Black box still flashing after attaching MCG to Gunfighter
Have a read on this post/thread:
viewtopic.php?p=28475#p28475
viewtopic.php?p=28475#p28475
Re: Black box still flashing after attaching MCG to Gunfighter
Yes, I set up using that, but when I press the centre button on Master mode, I end up with centre and two other two buttons. Gate Cont does not register a press at all in the test screen. I also see the axis moving.
Happy to accept I am doing this all wrong.
Happy to accept I am doing this all wrong.
Who is online
Users browsing this forum: No registered users and 44 guests