MCG Pro X Axis Spiking

Moderator: AdminGroup

Wrong Way
Posts: 6
Joined: Thu Apr 19, 2018 2:47
Has thanked: 1 time

MCG Pro X Axis Spiking

Postby Wrong Way » Thu Apr 19, 2018 3:27

Hello, I'm getting terrible spiking in the x-axis

Model: VKBGF002 Rev MKII
Firmware: BB GF v1.91.1
Springs: x #50, y #50
Cams: #10
Software: Device Config v0.83.85, ZBootloader-C v1.11
Attachments
Scr180418185853.jpg
01.JPG
02.JPG

Ron61
Posts: 3261
Joined: Tue Jan 15, 2013 23:56
Location: г.Минск
Has thanked: 44 times
Been thanked: 637 times

MCG Pro X Axis Spiking

Postby Ron61 » Thu Apr 19, 2018 12:40

Show screenshots of tabs of physical and logical axes.

Wrong Way
Posts: 6
Joined: Thu Apr 19, 2018 2:47
Has thanked: 1 time

MCG Pro X Axis Spiking

Postby Wrong Way » Fri Apr 20, 2018 0:56

Sorry, I could only post three images for some reason, then had to wait for the moderator.
Attachments
05.JPG
04.JPG
03.JPG

Wrong Way
Posts: 6
Joined: Thu Apr 19, 2018 2:47
Has thanked: 1 time

MCG Pro X Axis Spiking

Postby Wrong Way » Fri Apr 20, 2018 1:00

More screen caps.
Attachments
08.JPG
07.JPG
06.JPG

Ron61
Posts: 3261
Joined: Tue Jan 15, 2013 23:56
Location: г.Минск
Has thanked: 44 times
Been thanked: 637 times

MCG Pro X Axis Spiking

Postby Ron61 » Fri Apr 20, 2018 11:07

I can advise you to install extreme beta versions of the configurator and firmware.
1. add the lines in the corresponding sections to the zconfig.ini file (which will appear after the first launch of the configurator in the folder where it is installed), as in the screenshot
2. after restarting the configurator, reset the settings to default, which appeared with the same name button
3. make calibration on all axes
4. if there are unused axes (for example, TRudder is not directly connected to the BlackBox Gunfighter - this is the 7th physical axis), then in the Input, set Virtual for them (now there is D-Mars)

8.png

YAGA
Posts: 20
Joined: Wed Jan 31, 2018 20:41
Been thanked: 2 times

MCG Pro X Axis Spiking

Postby YAGA » Fri Apr 20, 2018 17:50

I had the exact same issue, as have many others. Mine was fixed by replacing the wiring between the USB pass through and the board. It also fixed phantom button presses.

Wrong Way
Posts: 6
Joined: Thu Apr 19, 2018 2:47
Has thanked: 1 time

MCG Pro X Axis Spiking

Postby Wrong Way » Sat Apr 28, 2018 16:43

The beta firmware seems to have solved the problem. I've been using the joystick with the new firmware for three days, and I haven't had the problem.

Thank you so much!

Ron61
Posts: 3261
Joined: Tue Jan 15, 2013 23:56
Location: г.Минск
Has thanked: 44 times
Been thanked: 637 times

MCG Pro X Axis Spiking

Postby Ron61 » Sat Apr 28, 2018 18:40

You're welcome.


Return to “Technical Support”

Who is online

Users browsing this forum: No registered users and 29 guests