Calibration after flashing v1.91F

Moderator: AdminGroup

rwalker
Posts: 15
Joined: Thu Jan 04, 2018 19:47
Been thanked: 1 time

Calibration after flashing v1.91F

Postby rwalker » Tue Jan 16, 2018 19:11

Hi,

I flashed to the latest firmware, v1.91F, after flashing I:
1. Clicked the default button
2. Calibrated.

Calibration seemed to work fine, but after I click end calibration some buttons show as pressed in the test tab. They were not shown as pressed before the calibration started. I've tried repeating the steps a few times now always with the same result. I had previously flashed v1.91E a few days ago with no problems. See the image below:
Capture.PNG

rwalker
Posts: 15
Joined: Thu Jan 04, 2018 19:47
Been thanked: 1 time

Re: Calibration after flashing v1.91F

Postby rwalker » Tue Jan 16, 2018 19:19

hmm, very strange. I calibrated a couple more times. One time after calibration, the buttons didn't show as pressed. I exited Device config, came back in, lights were still not on. I thought it was fixed. I clicked the Axes1 tab and checked the range of the axis, all seemed good. Clicked back on the test button and saw this:
Capture 2.PNG
Last edited by rwalker on Tue Jan 16, 2018 19:44, edited 1 time in total.

rwalker
Posts: 15
Joined: Thu Jan 04, 2018 19:47
Been thanked: 1 time

Re: Calibration after flashing v1.91F

Postby rwalker » Tue Jan 16, 2018 19:23

Just went back to 1.91E and have no problems.

Ron61
Posts: 930
Joined: Tue Jan 15, 2013 23:56
Location: г.Минск
Has thanked: 17 times
Been thanked: 173 times

Re: Calibration after flashing v1.91F

Postby Ron61 » Tue Jan 16, 2018 19:39

Show a screenshot of the tab Global-> Common version 1.91F.

rwalker
Posts: 15
Joined: Thu Jan 04, 2018 19:47
Been thanked: 1 time

Re: Calibration after flashing v1.91F

Postby rwalker » Tue Jan 16, 2018 21:14

Well, I went back to 1.91F and now I don't see the issue. Just to answer your question, the Global/Common page:
Capture 3.PNG

Ron61
Posts: 930
Joined: Tue Jan 15, 2013 23:56
Location: г.Минск
Has thanked: 17 times
Been thanked: 173 times

Re: Calibration after flashing v1.91F

Postby Ron61 » Tue Jan 16, 2018 21:50

Once the problem has disappeared - wonderful. I remember, in earlier versions, it was like that, if there was not a check-box Map.

Drano
Posts: 58
Joined: Sun Oct 01, 2017 5:00
Location: USA, East coast
Has thanked: 1 time
Been thanked: 10 times

Re: Calibration after flashing v1.91F

Postby Drano » Tue Jan 16, 2018 22:15

FWIW I had that happen too. Hitting the "set" button cleared it.
Gunfighter MkI w/MCG-Pro Grip
#10 Cams
#30 Springs
FW: v1.94F
VKBDevconfig: v0.87.98
Zbootloader: v1. 15

CPU: i7-6700-K
GPU: MSI 1060 6GB GamingX
Mem: 16GB Corsair Vengeance
PSU: Corsair ZX1000
Mobo: Asus P8Z68 Deluxe
Win7/64

rwalker
Posts: 15
Joined: Thu Jan 04, 2018 19:47
Been thanked: 1 time

Re: Calibration after flashing v1.91F

Postby rwalker » Tue Jan 16, 2018 22:46

ok, this is getting weirder. I did nothing but start VKB Device Config again just now. The second image listed above, the one with many buttons "on", is back. Global/Common is the same as I already attached. When did you hit "set"? I tried it and it just said something about no new data.

Drano
Posts: 58
Joined: Sun Oct 01, 2017 5:00
Location: USA, East coast
Has thanked: 1 time
Been thanked: 10 times

Re: Calibration after flashing v1.91F

Postby Drano » Wed Jan 17, 2018 3:50

Click default, then click set(important) , THEN calibrate. Gotta do that because the device isn't "ready" until you do. When you click end calibr, the device restarts and you should be ok. I can't replicate it as it only happened after the flash and it's gone now. But you're not crazy! I saw it too! I think I just happened to have the test buttons screen open before I did anything else and all those buttons showed pressed. Definitely a Wtf moment!
Gunfighter MkI w/MCG-Pro Grip
#10 Cams
#30 Springs
FW: v1.94F
VKBDevconfig: v0.87.98
Zbootloader: v1. 15

CPU: i7-6700-K
GPU: MSI 1060 6GB GamingX
Mem: 16GB Corsair Vengeance
PSU: Corsair ZX1000
Mobo: Asus P8Z68 Deluxe
Win7/64

rwalker
Posts: 15
Joined: Thu Jan 04, 2018 19:47
Been thanked: 1 time

Re: Calibration after flashing v1.91F

Postby rwalker » Wed Jan 17, 2018 5:39

I'll try that, I did click default each time, but I'm pretty sure I didn't click set after that.

Update: clicking set after default..seems to be working now..crossing fingers! Thanks for help.

rwalker
Posts: 15
Joined: Thu Jan 04, 2018 19:47
Been thanked: 1 time

Re: Calibration after flashing v1.91F

Postby rwalker » Thu Jan 18, 2018 21:53

Issue is back after flashing to 1.921. It is like the first picture (bottom row of buttons reporting being pressed). Made sure I clicked set at the same time as before, but then tried not clicking set after default as well. If I click restart from VKB Device Config, the lights go off for a little while, but come back on after some short time (< 10 minutes). I'll live with this for a while and see if any games have problems. Those aren't even buttons I can use anyways.

Drano
Posts: 58
Joined: Sun Oct 01, 2017 5:00
Location: USA, East coast
Has thanked: 1 time
Been thanked: 10 times

Re: Calibration after flashing v1.91F

Postby Drano » Thu Jan 18, 2018 22:34

You have to click set. Reason is when you click default it clears everything in VKBDevconfig. It's the default profile. You have to set that default profile to the stick in order to truely restore defaults. It's an important step. Without clicking set, while you've told VKBDevconfig to restore, you haven't sent that info to the stick. They both have to be on the same page. After that you must calibrate.

As I said I'd seen this too but haven't had it recur once I'd done all that. I'll be flashing to the new FW tonight probably.
Gunfighter MkI w/MCG-Pro Grip
#10 Cams
#30 Springs
FW: v1.94F
VKBDevconfig: v0.87.98
Zbootloader: v1. 15

CPU: i7-6700-K
GPU: MSI 1060 6GB GamingX
Mem: 16GB Corsair Vengeance
PSU: Corsair ZX1000
Mobo: Asus P8Z68 Deluxe
Win7/64

rwalker
Posts: 15
Joined: Thu Jan 04, 2018 19:47
Been thanked: 1 time

Re: Calibration after flashing v1.91F

Postby rwalker » Thu Jan 18, 2018 22:43

I did as mentioned: "Made sure I clicked set at the same time as before...", but just as a test I tried again without clicking set...And my current state is where I flashed, clicked default, click set, calibrated. Lights are on...I would also mention that previous firmware updates don't have this behavior.

Drano
Posts: 58
Joined: Sun Oct 01, 2017 5:00
Location: USA, East coast
Has thanked: 1 time
Been thanked: 10 times

Re: Calibration after flashing v1.91F

Postby Drano » Fri Jan 19, 2018 2:13

OK I flashed to 1.921 and this is what I got as I went thru
Before doing anything. My profile:
1Devconfig pre flash.jpg

Then after flash:
2Devconfig post flast.jpg

After hitting default and set:
3Default_Set.jpg

Continued next post........
Gunfighter MkI w/MCG-Pro Grip
#10 Cams
#30 Springs
FW: v1.94F
VKBDevconfig: v0.87.98
Zbootloader: v1. 15

CPU: i7-6700-K
GPU: MSI 1060 6GB GamingX
Mem: 16GB Corsair Vengeance
PSU: Corsair ZX1000
Mobo: Asus P8Z68 Deluxe
Win7/64

Drano
Posts: 58
Joined: Sun Oct 01, 2017 5:00
Location: USA, East coast
Has thanked: 1 time
Been thanked: 10 times

Re: Calibration after flashing v1.91F

Postby Drano » Fri Jan 19, 2018 2:15

And finally after calibrating, hit set, add my profile. Back to normal:

4Post Cal_set.jpg
Gunfighter MkI w/MCG-Pro Grip
#10 Cams
#30 Springs
FW: v1.94F
VKBDevconfig: v0.87.98
Zbootloader: v1. 15

CPU: i7-6700-K
GPU: MSI 1060 6GB GamingX
Mem: 16GB Corsair Vengeance
PSU: Corsair ZX1000
Mobo: Asus P8Z68 Deluxe
Win7/64


Return to “Technical Support”

Who is online

Users browsing this forum: rtrski and 2 guests