Hi,
I flashed to the latest firmware, v1.91F, after flashing I:
1. Clicked the default button
2. Calibrated.
Calibration seemed to work fine, but after I click end calibration some buttons show as pressed in the test tab. They were not shown as pressed before the calibration started. I've tried repeating the steps a few times now always with the same result. I had previously flashed v1.91E a few days ago with no problems. See the image below:
Calibration after flashing v1.91F
Moderator: AdminGroup
Re: Calibration after flashing v1.91F
hmm, very strange. I calibrated a couple more times. One time after calibration, the buttons didn't show as pressed. I exited Device config, came back in, lights were still not on. I thought it was fixed. I clicked the Axes1 tab and checked the range of the axis, all seemed good. Clicked back on the test button and saw this:
Last edited by rwalker on Tue Jan 16, 2018 19:44, edited 1 time in total.
Re: Calibration after flashing v1.91F
Well, I went back to 1.91F and now I don't see the issue. Just to answer your question, the Global/Common page:
-
- Posts: 313
- Joined: Sun Oct 01, 2017 5:00
- Location: Representin' the 302
- Has thanked: 20 times
- Been thanked: 86 times
Re: Calibration after flashing v1.91F
FWIW I had that happen too. Hitting the "set" button cleared it.
Gunfighter MkI w/MkIII update + MCG-Pro Grip
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Re: Calibration after flashing v1.91F
ok, this is getting weirder. I did nothing but start VKB Device Config again just now. The second image listed above, the one with many buttons "on", is back. Global/Common is the same as I already attached. When did you hit "set"? I tried it and it just said something about no new data.
-
- Posts: 313
- Joined: Sun Oct 01, 2017 5:00
- Location: Representin' the 302
- Has thanked: 20 times
- Been thanked: 86 times
Re: Calibration after flashing v1.91F
Click default, then click set(important) , THEN calibrate. Gotta do that because the device isn't "ready" until you do. When you click end calibr, the device restarts and you should be ok. I can't replicate it as it only happened after the flash and it's gone now. But you're not crazy! I saw it too! I think I just happened to have the test buttons screen open before I did anything else and all those buttons showed pressed. Definitely a Wtf moment!
Gunfighter MkI w/MkIII update + MCG-Pro Grip
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Re: Calibration after flashing v1.91F
I'll try that, I did click default each time, but I'm pretty sure I didn't click set after that.
Update: clicking set after default..seems to be working now..crossing fingers! Thanks for help.
Update: clicking set after default..seems to be working now..crossing fingers! Thanks for help.
Re: Calibration after flashing v1.91F
Issue is back after flashing to 1.921. It is like the first picture (bottom row of buttons reporting being pressed). Made sure I clicked set at the same time as before, but then tried not clicking set after default as well. If I click restart from VKB Device Config, the lights go off for a little while, but come back on after some short time (< 10 minutes). I'll live with this for a while and see if any games have problems. Those aren't even buttons I can use anyways.
-
- Posts: 313
- Joined: Sun Oct 01, 2017 5:00
- Location: Representin' the 302
- Has thanked: 20 times
- Been thanked: 86 times
Re: Calibration after flashing v1.91F
You have to click set. Reason is when you click default it clears everything in VKBDevconfig. It's the default profile. You have to set that default profile to the stick in order to truely restore defaults. It's an important step. Without clicking set, while you've told VKBDevconfig to restore, you haven't sent that info to the stick. They both have to be on the same page. After that you must calibrate.
As I said I'd seen this too but haven't had it recur once I'd done all that. I'll be flashing to the new FW tonight probably.
As I said I'd seen this too but haven't had it recur once I'd done all that. I'll be flashing to the new FW tonight probably.
Gunfighter MkI w/MkIII update + MCG-Pro Grip
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Re: Calibration after flashing v1.91F
I did as mentioned: "Made sure I clicked set at the same time as before...", but just as a test I tried again without clicking set...And my current state is where I flashed, clicked default, click set, calibrated. Lights are on...I would also mention that previous firmware updates don't have this behavior.
-
- Posts: 313
- Joined: Sun Oct 01, 2017 5:00
- Location: Representin' the 302
- Has thanked: 20 times
- Been thanked: 86 times
Re: Calibration after flashing v1.91F
OK I flashed to 1.921 and this is what I got as I went thru
Before doing anything. My profile:
Then after flash:
After hitting default and set:
Continued next post........
Before doing anything. My profile:
Then after flash:
After hitting default and set:
Continued next post........
Gunfighter MkI w/MkIII update + MCG-Pro Grip
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
-
- Posts: 313
- Joined: Sun Oct 01, 2017 5:00
- Location: Representin' the 302
- Has thanked: 20 times
- Been thanked: 86 times
Re: Calibration after flashing v1.91F
And finally after calibrating, hit set, add my profile. Back to normal:
Gunfighter MkI w/MkIII update + MCG-Pro Grip
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Avia S Cams
2x #30A Springs
FW:v2.13F
Devconfig: v92.78
Zbootloader: v2.01
Asus Strix X570-E Gaming
Ryzen9 5800X3D
Asus Strix 3080 12GB
32GB Corsair Vengeance PC3600
EVGA G6 1000W
Reverb G2V2
Win10/64
Who is online
Users browsing this forum: No registered users and 107 guests