Need help updating firmware.
Moderator: AdminGroup
Need help updating firmware.
I tried running bootloader from cfg software without having the zbootloader in the same folder and now i'm stuck in this screen with all buttons disabled.
Re: Need help updating firmware.
I was able to make the buttons show up by unplugging the usb cable, now when i flash the new firmware i'm getting "write error".
Re: Need help updating firmware.
Now i managed for cfg not showing my joysticks at all.
I tried restarting my computer and unplugging them and still they're not showing up in the cfg software.
I tried restarting my computer and unplugging them and still they're not showing up in the cfg software.
Re: Need help updating firmware.
I have also come across this error, see attached image.
- Attachments
-
- Capture1.PNG (6.85 KiB) Viewed 6029 times
Re: Need help updating firmware.
Just launch zbootloader. I hope you will see OK message)) Update firmware or reset controller without upgrade.
Руководство пользователя по контроллерам VKB (VKB controllers User Guide) Ru&En
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
https://disk.yandex.ru/d/LlqiYtIrIetBOQ
Re: Need help updating firmware.
Thanks for the quick help!
See attached pic.
I think i managed to install the new firmware but the blackbox paired with the mcg pro still blinks red light.
Is there a way to make it solid yellow like it was before?
See attached pic.
I think i managed to install the new firmware but the blackbox paired with the mcg pro still blinks red light.
Is there a way to make it solid yellow like it was before?
Last edited by gavros777 on Sun Jan 07, 2018 13:53, edited 1 time in total.
Re: Need help updating firmware.
gavros777 wrote:See attached pic
... and in it I see 2 (two) joysticks.
Do you have 2 devices connected to your computer?
Or, 2 Black Boxes?
Either way, please post the EXTERNAL tab screenshot.
Best Regards,
AeroGator
AeroGator
Re: Need help updating firmware.
AeroGator wrote:gavros777 wrote:See attached pic
... and in it I see 2 (two) joysticks.
Do you have 2 devices connected to your computer?
Or, 2 Black Boxes?
Either way, please post the EXTERNAL tab screenshot.
i use a dual gunfighter pro joystick setup, with the mcg pro on the right side.
each joystick has its own black box.
excuse my noobness but which tab are you referring at, i see action, tools and settings tabs. is the external tab one of those 3?
Re: Need help updating firmware.
gavros777 wrote:excuse my noobness but which tab are you referring at, i see action, tools and settings tabs. is the external tab one of those 3?
A guy with a dual setup cannot be called a noob in any case!
Best Regards,
AeroGator
AeroGator
Re: Need help updating firmware.
gavros777 wrote:See attachment.
1 - what's on your 2nd base?
2 - whatever it is, only keep 1 base connected when configuring it, otherwise the system (and we poor techsupport elves and fairies) get screwed up
3 - I have a suspicion you did not default the system after calibration... true?
Best Regards,
AeroGator
AeroGator
Re: Need help updating firmware.
1) On one base i have the mcg pro and on the other the kg12.
2,3)I had calibrated them in the past, how do i turn them back to default?
Also after i turn them back to default should i try to flash the firmware again at 1 base at a time?
2,3)I had calibrated them in the past, how do i turn them back to default?
Also after i turn them back to default should i try to flash the firmware again at 1 base at a time?
Re: Need help updating firmware.
gavros777 wrote:how do i turn them back to default?
Also after i turn them back to default should i try to flash the firmware again at 1 base at a time?
Here is HOW TO set the system to default (exceptionally well written by @rrohde): https://forums.eagle.ru/showpost.php?p=3349350&postcount=110
In that post you will also see links to a couple of posts at this forum.
I understand you - this software utility can be a bit scary and tricky but in fact after you master it it will give you really full control over your devices. Worth some time wasted on getting used to it.
And no, after you default them you don't need to reflash the firmware (presuming you had already done it and the current FW is the newest). Defaulting the system is the final step of all the FW update procedure. Then you re-calibrate the stick (re-calibrate is NOT equal to re-flash), and go flying.
Best Regards,
AeroGator
AeroGator
Who is online
Users browsing this forum: No registered users and 38 guests