Gladiator Pro Warthog Adapter
Moderator: AdminGroup
Re: Warthog Adapter for Gladiator Pro not working
Cant load the Warthog config file says 'Get Feature Fault' Trying to figure this out that it has to have the config file to see button even in VKB Joytester application? Wires are good I haven't even screwed the handle together. I have it installed with the half handle cover off. I have to disconnect it each time I run it from the USB port also because it goes dead when I try to install Config file.
- rrohde
- Posts: 618
- Joined: Thu Oct 08, 2015 9:28
- Location: USA
- Has thanked: 681 times
- Been thanked: 242 times
Re: Warthog Adapter for Gladiator Pro not working
Try this version of the VKBdevCfg:
http://vkbcontrollers.com/?product=vkb- ... n-software
And try this version of WIZZO:
http://vkbcontrollers.com/?product=wizz ... e-software
If this doesn't do it, we might have to get the attention of some of the software guys.
http://vkbcontrollers.com/?product=vkb- ... n-software
And try this version of WIZZO:
http://vkbcontrollers.com/?product=wizz ... e-software
If this doesn't do it, we might have to get the attention of some of the software guys.
VKB North America
https://VKBcontrollers.com
https://VKBcontrollers.com
Re: Gladiator Pro Warthog Adapter
I put the VK config file and wizzo file you asked me to use in a new folder and ran them. When I load the Warthog config file and try to set it it gives me 'CPUID Error' and makes my stick go dead. I have to unplug it from the USB port each time I try to run and set the Warthog file. The program seems to be working ok because I can create my own config file and save them and load them but it will not let me set the Warthog config file without locking the stick up and getting the CPUID ERROR.
-
- Posts: 3263
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: Gladiator Pro Warthog Adapter
You have version 1.801, which may not work properly. It is necessary to update the firmware to 1.80 A, which is located http://forum.vkb-sim.pro/viewtopic.php?f=15&t=908 here. And then load the profile. How to fill in, we read http://forum.vkb-sim.pro/viewtopic.php?f=25&t=2355#p23008 it.
Re: Gladiator Pro Warthog Adapter
The stick will not flash to V1.80 8
I have tried to run Bootloader in Wizzo and get cant find joystick and using latest Bootloaderc087
I have tried to run Bootloader in Wizzo and get cant find joystick and using latest Bootloaderc087
-
- Posts: 3263
- Joined: Tue Jan 15, 2013 23:56
- Location: г.Минск
- Has thanked: 44 times
- Been thanked: 637 times
Re: Gladiator Pro Warthog Adapter
ZBootloader-C.exe file is put in the folder with the configurator and there press the red button Bootloader. Some models of the mice and their software did not allow flash controller. Try temporarily disable all unnecessary and leave only the keyboard and mouse. Or try on a different computer, laptop. While there is no green - flash is not possible.
Re: Gladiator Pro Warthog Adapter
Thanks Ron61 and others. I disconnected it from my Gaming Desktop and hooked up to Gaming Laptop. I removed everything that was hooked up to including all 'Dongles" mice. I first tried to boot it with the Bootloader Program but got the 'RED Light' knowing what the red light was for saved me a lot of frustration. I then tried the Configurator program not Wizzo and it didn't work so I shut system down and restarted plugged the joystick in to different USB and ran Configurator again and got the Green light when I booted it to V1.08. I was able to install the Warthog CFG file and now I have buttons working. Gonna take a break and put stick back together later been trying to figure this out for two days. Thanks for sending me the picture of where the connector block installs 'under the exsiting warthog connector block. I kinda figured that's where it should go. My next project will be to see If my VKB rudders will work now with my stick. Thanks all for help this was a rough learning curve
- rrohde
- Posts: 618
- Joined: Thu Oct 08, 2015 9:28
- Location: USA
- Has thanked: 681 times
- Been thanked: 242 times
Re: Gladiator Pro Warthog Adapter
Glad it's working now! Thanks Ron61 for your support!
VKB North America
https://VKBcontrollers.com
https://VKBcontrollers.com
Re: Gladiator Pro Warthog Adapter
Got the Stick all put back together and hooked up to my Gaming Desktop and buttons are all working. Really nice to have to be able to use the Warthog stick with a good gimbal system. I put the W cam in on pitch and put the blue springs on instead of the Black one that came with the Adapter kit. The tension is still more than I want and would like to reduce it down. What are the color codes for springs I know that white is what I had in it before putting the Warthog on but the tension was to light and stick wouldn't stay centered. What is the next tension color code up?
- rrohde
- Posts: 618
- Joined: Thu Oct 08, 2015 9:28
- Location: USA
- Has thanked: 681 times
- Been thanked: 242 times
Re: Gladiator Pro Warthog Adapter
From weak to strong: white, yellow, green, blue, black; the default spring is yellow.
VKB North America
https://VKBcontrollers.com
https://VKBcontrollers.com
Who is online
Users browsing this forum: No registered users and 33 guests