Search found 3274 matches
- Fri Feb 16, 2024 12:59
- Forum: Программное обеспечение
- Topic: T-Link для T-Rudder / T-Link for T-Rudder.
- Replies: 70
- Views: 86509
Re: T-Link для T-Rudder / T-Link for T-Rudder.
Ни на одном из ваших скриншотов из T-link статус не поменялся на Sending Data (когда кнопка назначена на мамбе), а без этого работать не будет. Чтоб увидеть отклик педалей в Joy Tester, нужно выбрать соответствующее устройство. Вряд-ли они появятся на руде от VPC.
- Fri Feb 16, 2024 10:35
- Forum: Программное обеспечение
- Topic: T-Link для T-Rudder / T-Link for T-Rudder.
- Replies: 70
- Views: 86509
Re: T-Link для T-Rudder / T-Link for T-Rudder.
Сбросьте настройки на Tiny в дефолт и попробуйте снова.
- Fri Feb 16, 2024 10:23
- Forum: Программное обеспечение
- Topic: T-Link для T-Rudder / T-Link for T-Rudder.
- Replies: 70
- Views: 86509
Re: T-Link для T-Rudder / T-Link for T-Rudder.
Сильно сомневаюсь, что кнопка может быть назначена на стороннем девайсе. Попробуйте на мамбе назначить и новую версию, отсюда.
- Fri Feb 16, 2024 10:12
- Forum: Программное обеспечение
- Topic: T-Link для T-Rudder / T-Link for T-Rudder.
- Replies: 70
- Views: 86509
Re: T-Link для T-Rudder / T-Link for T-Rudder.
Ага, никакого рычага тормоза (оси) нет на ручке. Попробуйте настроить в соответствии с документом, скриншоты приветствуются.
- Thu Feb 15, 2024 23:02
- Forum: Программное обеспечение
- Topic: T-Link для T-Rudder / T-Link for T-Rudder.
- Replies: 70
- Views: 86509
Re: T-Link для T-Rudder / T-Link for T-Rudder.
Свою конфигурацию девайсов озвучьте хотя б, для начала. Решение тут, без T-Link.
- Tue Feb 13, 2024 11:16
- Forum: Technical Support
- Topic: Gunfighter 1 / MCG X-Axis Failure
- Replies: 6
- Views: 552
Re: Gunfighter 1 / MCG X-Axis Failure
Write to the seller or sales@vkb-sim.pro with a photo attached.
- Mon Feb 12, 2024 19:44
- Forum: Technical Support
- Topic: Gunfighter 1 / MCG X-Axis Failure
- Replies: 6
- Views: 552
Re: Gunfighter 1 / MCG X-Axis Failure
Check the space under the sensor. Perhaps some speck or shavings appeared that stuck to the magnet.
There were cases when the Grover washer stuck.
Well, check the cable itself and the reliability of the contact in the connector.
There were cases when the Grover washer stuck.
Well, check the cable itself and the reliability of the contact in the connector.
- Thu Feb 08, 2024 19:33
- Forum: Technical Support
- Topic: GNX SEM-V
- Replies: 3
- Views: 500
Re: GNX SEM-V
See this picture.
- Tue Feb 06, 2024 18:16
- Forum: Тех. поддержка
- Topic: Как искать шляпки на министики ВКБ?
- Replies: 4
- Views: 700
Re: Как искать шляпки на министики ВКБ?
По второму вопросу - лучше использовать рычаг, которым можно дозировать усилие.
- Tue Feb 06, 2024 18:11
- Forum: Technical Support
- Topic: Unable to program flap detents
- Replies: 11
- Views: 901
Re: Unable to program flap detents
Sent more detailed instructions.
- Mon Feb 05, 2024 14:22
- Forum: Technical Support
- Topic: Unable to program flap detents
- Replies: 11
- Views: 901
Re: Unable to program flap detents
Most likely the factory settings of the flap and landing gear axes have been lost. Instructions for calibration will be sent via PM.
- Mon Feb 05, 2024 13:23
- Forum: Technical Support
- Topic: Which firmware.
- Replies: 8
- Views: 4010
Re: Which firmware.
This depends on when your NXT EVO was manufactured. In the first batches kmz41 sensors were used, in subsequent batches others were installed. And any firmware will work, only the main axes will be inverted. It is by this criterion that you can determine what sensors are worth and adhere to the corr...
- Sat Feb 03, 2024 10:13
- Forum: Technical Support
- Topic: Unable to program flap detents
- Replies: 11
- Views: 901
Re: Unable to program flap detents
I stop understanding what is written. Make a video, maybe it will help in understanding.
- Sat Feb 03, 2024 9:16
- Forum: Technical Support
- Topic: Cannot calibrate custom axis
- Replies: 2
- Views: 254
Re: Cannot calibrate custom axis
Show the Profile-Axes tab from the configurator indicating the virtual axis.
- Fri Feb 02, 2024 23:59
- Forum: Technical Support
- Topic: Unable to program flap detents
- Replies: 11
- Views: 901
Re: Unable to program flap detents
I’ll ask again - how many physical positions does the flap lever have? When changing the firmware, you do not need to configure the address or number of positions. This is done once when changing the liner and that’s it.