Сильно сомневаюсь, что кнопка может быть назначена на стороннем девайсе. Попробуйте на мамбе назначить и новую версию, отсюда.
Search found 3272 matches
- Fri Feb 16, 2024 10:23
- Forum: Программное обеспечение
- Topic: T-Link для T-Rudder / T-Link for T-Rudder.
- Replies: 70
- Views: 82339
- Fri Feb 16, 2024 10:12
- Forum: Программное обеспечение
- Topic: T-Link для T-Rudder / T-Link for T-Rudder.
- Replies: 70
- Views: 82339
Re: T-Link для T-Rudder / T-Link for T-Rudder.
Ага, никакого рычага тормоза (оси) нет на ручке. Попробуйте настроить в соответствии с документом, скриншоты приветствуются.
- Thu Feb 15, 2024 23:02
- Forum: Программное обеспечение
- Topic: T-Link для T-Rudder / T-Link for T-Rudder.
- Replies: 70
- Views: 82339
Re: T-Link для T-Rudder / T-Link for T-Rudder.
Свою конфигурацию девайсов озвучьте хотя б, для начала. Решение тут, без T-Link.
- Tue Feb 13, 2024 11:16
- Forum: Technical Support
- Topic: Gunfighter 1 / MCG X-Axis Failure
- Replies: 6
- Views: 285
Re: Gunfighter 1 / MCG X-Axis Failure
Write to the seller or sales@vkb-sim.pro with a photo attached.
- Mon Feb 12, 2024 19:44
- Forum: Technical Support
- Topic: Gunfighter 1 / MCG X-Axis Failure
- Replies: 6
- Views: 285
Re: Gunfighter 1 / MCG X-Axis Failure
Check the space under the sensor. Perhaps some speck or shavings appeared that stuck to the magnet.
There were cases when the Grover washer stuck.
Well, check the cable itself and the reliability of the contact in the connector.
There were cases when the Grover washer stuck.
Well, check the cable itself and the reliability of the contact in the connector.
- Thu Feb 08, 2024 19:33
- Forum: Technical Support
- Topic: GNX SEM-V
- Replies: 3
- Views: 209
Re: GNX SEM-V
See this picture.
- Tue Feb 06, 2024 18:16
- Forum: Тех. поддержка
- Topic: Как искать шляпки на министики ВКБ?
- Replies: 4
- Views: 339
Re: Как искать шляпки на министики ВКБ?
По второму вопросу - лучше использовать рычаг, которым можно дозировать усилие.
- Tue Feb 06, 2024 18:11
- Forum: Technical Support
- Topic: Unable to program flap detents
- Replies: 11
- Views: 572
Re: Unable to program flap detents
Sent more detailed instructions.
- Mon Feb 05, 2024 14:22
- Forum: Technical Support
- Topic: Unable to program flap detents
- Replies: 11
- Views: 572
Re: Unable to program flap detents
Most likely the factory settings of the flap and landing gear axes have been lost. Instructions for calibration will be sent via PM.
- Mon Feb 05, 2024 13:23
- Forum: Technical Support
- Topic: Which firmware.
- Replies: 8
- Views: 3581
Re: Which firmware.
This depends on when your NXT EVO was manufactured. In the first batches kmz41 sensors were used, in subsequent batches others were installed. And any firmware will work, only the main axes will be inverted. It is by this criterion that you can determine what sensors are worth and adhere to the corr...
- Sat Feb 03, 2024 10:13
- Forum: Technical Support
- Topic: Unable to program flap detents
- Replies: 11
- Views: 572
Re: Unable to program flap detents
I stop understanding what is written. Make a video, maybe it will help in understanding.
- Sat Feb 03, 2024 9:16
- Forum: Technical Support
- Topic: Cannot calibrate custom axis
- Replies: 2
- Views: 229
Re: Cannot calibrate custom axis
Show the Profile-Axes tab from the configurator indicating the virtual axis.
- Fri Feb 02, 2024 23:59
- Forum: Technical Support
- Topic: Unable to program flap detents
- Replies: 11
- Views: 572
Re: Unable to program flap detents
I’ll ask again - how many physical positions does the flap lever have? When changing the firmware, you do not need to configure the address or number of positions. This is done once when changing the liner and that’s it.
- Fri Feb 02, 2024 19:49
- Forum: Technical Support
- Topic: Unable to program flap detents
- Replies: 11
- Views: 572
Re: Unable to program flap detents
At what point in this video do you get the error? After resetting to default and auto-configuring, which buttons are pressed when moving the flap lever? How many positions is the lever set to?
- Thu Feb 01, 2024 1:10
- Forum: Technical Support
- Topic: Need config help, 4 position flaps and 9th axis not working
- Replies: 15
- Views: 859
Re: Need config help, 4 position flaps and 9th axis not working
Try updating the configurator and firmware.
After the update, you must reconfigure the devices connected to the GL NXT Evo.
After the update, you must reconfigure the devices connected to the GL NXT Evo.