Search found 3272 matches
- Mon May 31, 2021 18:34
- Forum: Technical Support
- Topic: mcg pro twist flip trigger springeyness gone
- Replies: 10
- Views: 3092
Re: mcg pro twist flip trigger springeyness gone
There is nothing complicated there. Unscrew the 2 screws at the bottom of the right half of the grip. Unscrew 6 screws on the left half (to access one screw, you need a Phillips screwdriver with a length of at least 45 mm). Having removed the right half, we turn off the only self-tapping screw that ...
- Mon May 31, 2021 16:17
- Forum: Technical Support
- Topic: mcg pro twist flip trigger springeyness gone
- Replies: 10
- Views: 3092
Re: mcg pro twist flip trigger springeyness gone
Most likely something happened to the return spring. You need to disassemble the handle and get to it. And only then it will become clear what to do next.
- Mon May 31, 2021 16:11
- Forum: Тех. поддержка
- Topic: Апгрейд стокового NJoy32 v1,27 до NJoy32 Pro
- Replies: 75
- Views: 62001
Re: Апгрейд стокового NJoy32 v1,27 до NJoy32 Pro
А выбора особого и нет. Берите крайнее всё для Кинг Кобры.
- Wed May 26, 2021 23:02
- Forum: Technical Support
- Topic: Roll axis spikes on Warthog with Gunfighter base
- Replies: 3
- Views: 1389
Re: Roll axis spikes on Warthog with Gunfighter base
Check out this thread.
- Wed May 26, 2021 22:54
- Forum: Technical Support
- Topic: Slow support - how to contact VKB directly?
- Replies: 8
- Views: 2464
Re: Slow support - how to contact VKB directly?
Instead of such a long post, I advise you to show screenshots from the configurator of the Global-External, Profile-Axes, Test-External devices tabs.
- Tue May 25, 2021 8:26
- Forum: General discussions
- Topic: VKB Gunfighter MKIII Base Dimension
- Replies: 2
- Views: 2440
Re: VKB Gunfighter MKIII Base Dimension
Is that okay?
- Mon May 24, 2021 9:45
- Forum: Technical Support
- Topic: Gladiator NXT: Mouse Mapping to Mini-Stick / No Axis
- Replies: 4
- Views: 1840
Re: Gladiator NXT: Mouse Mapping to Mini-Stick / No Axis
Mouse axis settings have moved to the Povs-Output tab.
- Sun May 23, 2021 11:50
- Forum: Информация
- Topic: Представляем педали T-Rudder MkIV
- Replies: 67
- Views: 85326
Re: Представляем педали T-Rudder MkIV
Напишите на sales@vkb-sim.pro.
- Fri May 21, 2021 19:22
- Forum: Technical Support
- Topic: Stuck z-Axes Roll
- Replies: 49
- Views: 12133
Re: Stuck z-Axes Roll
Twist, of course, what else.
- Fri May 21, 2021 17:35
- Forum: Тех. поддержка
- Topic: Апгрейд стокового NJoy32 v1,27 до NJoy32 Pro
- Replies: 75
- Views: 62001
Re: Апгрейд стокового NJoy32 v1,27 до NJoy32 Pro
Пишите на sales@vkb-sim.pro. B заказывайте сразу апгрейд в KingCobra (минуя Pro), чтоб 2 раза не вставать.
- Fri May 21, 2021 17:27
- Forum: Technical Support
- Topic: Stuck z-Axes Roll
- Replies: 49
- Views: 12133
Re: Stuck z-Axes Roll
First, you need to eliminate such red and yellow peaks. These are the grip/stem pads. Only small and rare green "stumps" on the monitoring graph are allowed. Second, you can try turning the twist magnet 30-60 degrees. We put a mark with a marker and rotate it to the desired angle. Everythi...
- Thu May 20, 2021 19:49
- Forum: Technical Support
- Topic: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
- Replies: 10
- Views: 3113
Re: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
The damper screw does not come out more during rotation than in the photo. There is no thread, it is only on the square nut, which is spring loaded.
The backlash in the 4-pin output connector is standard - it is a plastic insert with pins in a metal case that moves. This does not affect the contact.
The backlash in the 4-pin output connector is standard - it is a plastic insert with pins in a metal case that moves. This does not affect the contact.
- Thu May 20, 2021 10:43
- Forum: Technical Support
- Topic: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
- Replies: 10
- Views: 3113
Re: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
Look closely at the soldering points of the connector to the board. It is possible to try to push them with the loop connected and monitor the quality of the connection in the configurator.
- Wed May 19, 2021 22:03
- Forum: Technical Support
- Topic: Gladiator Y-Axis BACK not registering
- Replies: 19
- Views: 4683
Re: Gladiator Y-Axis BACK not registering
Bingo! I need to take a closer look at the photo on the connecting cable.
- Wed May 19, 2021 20:02
- Forum: Technical Support
- Topic: VKBDevCfg-C cant find joystick [resolved]
- Replies: 16
- Views: 5030
Re: VKBDevCfg-C cant find joystick
You could try temporarily disconnecting all Razer devices. They can be the reason for this behavior.