Search found 802 matches
- Mon Jul 23, 2018 3:47
- Forum: Technical Support
- Topic: Having MCG Pro Issues, random intermittent button presses
- Replies: 76
- Views: 65978
Re: Having MCG Pro Issues, random intermittent button presses
Before digging for anything else, let us do the connection check. Please remove all the mechanics from the casing, dis- and reconnect the cables - especially the one that goes to/from the grip. Might be some oxidation on one of the pins. A few cycles of disconnection and reconnection usually cure th...
- Mon Jul 16, 2018 6:33
- Forum: Technical Support
- Topic: Response Curve in DevCfg appllied incorrectly
- Replies: 8
- Views: 5270
Re: Response Curve in DevCfg appllied incorrectly
Sorry for the delay; we will reply in a day or two.
- Fri Jul 13, 2018 15:50
- Forum: Technical Support
- Topic: T-Rudder MkIV RJ45 Connector
- Replies: 2
- Views: 2300
Re: T-Rudder MkIV RJ45 Connector
We use standard 8-wire ethernet cable, the same that runs between computers and hubs.
So the replacement can probably be found for a dollar or so in the nearest computer repair shop.
Happy flights!
So the replacement can probably be found for a dollar or so in the nearest computer repair shop.
Happy flights!
- Tue Jul 03, 2018 13:53
- Forum: Technical Support
- Topic: Loose In Y Axis
- Replies: 20
- Views: 10172
Re: Loose In Y Axis
The calibration is fine With all respect, I need the Qs answered in teh way they are put. Did you calibrate the device using VKB calibration tools? Y/N If Y, please in a few words describe how you did it. .... Did you loosen the tighter damper on Y? .... please show me the picture like the one I am...
- Tue Jul 03, 2018 9:55
- Forum: Technical Support
- Topic: Gladiator Pro MKII connection pin stuck causing red flashing led
- Replies: 4
- Views: 3481
Re: Gladiator Pro MKII connection pin stuck causing red flashing led
DKFlight wrote:Shipping it back for a replacement
I hate this happening but thank you for patience. I believe the next one will be good.
- Mon Jul 02, 2018 14:37
- Forum: Technical Support
- Topic: Gladiator Pro MKII connection pin stuck causing red flashing led
- Replies: 4
- Views: 3481
Re: Gladiator Pro MKII connection pin stuck causing red flashing led
I just received my new stick and was having problems with the flashing red led and no button on the stick being recognized. I found the info on flashing the firmware, used all the tools to check the stick and making sure the stick is properly seated. Then I took a close look and discovered one of t...
- Mon Jul 02, 2018 14:32
- Forum: Technical Support
- Topic: Upgrade kit
- Replies: 1
- Views: 1524
Re: Upgrade kit
Harryr1668 wrote:Does the upgrade kit also fix the play in the pitch axis on the Gladiator MK1 or does it just facilitate changing grips
Correct.
The slack around the center will be considerably reduced.
- Mon Jul 02, 2018 14:31
- Forum: Technical Support
- Topic: EU Website not fonctional ?
- Replies: 3
- Views: 3078
Re: EU Website not fonctional ?
ColdCraving wrote:since some days i want to place an order on a MCG but every time i log myself i get white page with just "error"
Any idea ?
Thanks for bringing it to our attention. It was up and running when I visited last, but let me see again. We will give a nudge to European guys in case it isn't.
- Sun Jul 01, 2018 15:32
- Forum: Technical Support
- Topic: T-Rudder MKIV not working
- Replies: 1
- Views: 3354
Re: T-Rudder MKIV not working
having issues getting my pedals working in DCS Welcome to the forum. Please check this out: http://forum.vkb-sim.pro/viewtopic.php?f=25&t=2762 - here are the guidelines to getting tech support fast. Please make yourself familiar with all questions listed there, as well as with the software diag...
- Sun Jul 01, 2018 13:21
- Forum: Technical Support
- Topic: gunfighter gimbal lag? (Star citizen)
- Replies: 4
- Views: 3431
Re: gunfighter gimbal lag? (Star citizen)
Good it worked out for you.
- Fri Jun 29, 2018 10:55
- Forum: Technical Support
- Topic: Loose In Y Axis
- Replies: 20
- Views: 10172
Re: Loose In Y Axis
a - the dumper on one of the axes is tuned to be stronger than on another (it is OK but not for now). So, to begin with, temporarily loosen the tighter dumper . .... 3 - use VKB calibration tools to re-calibrate the device . ...i reset it just in case. Did you calibrate the device using VKB calibra...
- Fri Jun 29, 2018 8:36
- Forum: Technical Support
- Topic: Loose In Y Axis
- Replies: 20
- Views: 10172
Re: Loose In Y Axis
The problem persists Sorry the numbers in the attached picture cannot be seen :roll: too small... you did everything right, as I asked you to keep the picture size smaller, but in this case exception can be made! Once again, sorry for wasting you time, but when you have a minute please upload a rea...
- Fri Jun 29, 2018 7:52
- Forum: Technical Support
- Topic: Loose In Y Axis
- Replies: 20
- Views: 10172
Re: Loose In Y Axis
Wow this is getting more interesting now.
Thanks for more info, we will chew on it.
Back to you later today.
YES it is damper of course. My bad.
Thanks for more info, we will chew on it.
Back to you later today.
YES it is damper of course. My bad.
- Fri Jun 29, 2018 5:54
- Forum: Technical Support
- Topic: Loose In Y Axis
- Replies: 20
- Views: 10172
Re: Loose In Y Axis
Heres some more Pics. From the pictures I get a suspicion that a - the dumper on one of the axes is tuned to be stronger than on another (it is OK but not for now). So, to begin with, temporarily loosen the tighter dumper. b - you calibrated the device using Windows tools. Never do that. 1 - go to ...
- Thu Jun 28, 2018 10:17
- Forum: Technical Support
- Topic: Loose In Y Axis
- Replies: 20
- Views: 10172
Re: Loose In Y Axis
:mrgreen: - pull the grip back (towards yourself) to the limit. - release it (take your hand off it and let it go freely). - make a screenshot of what the tester window shows. - repeat the same pushing the grip forward and letting it go, then left, then right. - resize all screenshots to a max 1000 ...