Search found 3281 matches
- Fri Mar 15, 2024 17:29
- Forum: Тех. поддержка
- Topic: Нелинейность отклика оси Y Gunfighter I
- Replies: 23
- Views: 1578
Re: Нелинейность отклика оси Y Gunfighter I
Проверку работы каналов датчика по совету Alex_Oz делали, результаты есть?
- Fri Mar 15, 2024 15:32
- Forum: Manuals and Howtos
- Topic: Need help with macros
- Replies: 3
- Views: 560
Re: Need help with macros
You have a little confusion in understanding the macro number and timing, but this can be easily corrected by looking at the picture. Let me explain that you can only run the second macro of 4 buttons, you just need to assign a button to it. As well as only the 5th of the two. Try lowering it from 5...
- Fri Mar 15, 2024 12:21
- Forum: Technical Support
- Topic: Twist Adapter for Gunfighter IV MCG Pro Grip question
- Replies: 1
- Views: 463
Re: Twist Adapter for Gunfighter IV MCG Pro Grip question
You can use an old plastic 3-pin connector. Make a 3 pin out of a 4 pin one. The white one can be attached to the spring.
- Fri Mar 15, 2024 9:25
- Forum: Technical Support
- Topic: MCG Ultimate Config Question
- Replies: 10
- Views: 687
Re: MCG Ultimate Config Question
That is great.
- Fri Mar 15, 2024 0:05
- Forum: Technical Support
- Topic: MCG Ultimate Config Question
- Replies: 10
- Views: 687
Re: MCG Ultimate Config Question
Change 11 to 7, write it to the controller with the Set button and it should work.
If it doesn’t work, reset it to default on the new firmware (2.17E) and try to calibrate again.
If it doesn’t work, reset it to default on the new firmware (2.17E) and try to calibrate again.
- Thu Mar 14, 2024 22:04
- Forum: Technical Support
- Topic: MCG Ultimate Config Question
- Replies: 10
- Views: 687
Re: MCG Ultimate Config Question
Select the pedals and take a screenshot. And show the Profile-Axes tab.
Try updating the firmware and configurator from here.
Try updating the firmware and configurator from here.
- Thu Mar 14, 2024 20:44
- Forum: Technical Support
- Topic: MCG Ultimate Config Question
- Replies: 10
- Views: 687
Re: MCG Ultimate Config Question
With pedals connected to BlackBox GF, reset them to default using the button in the configurator and show a screenshot of the Global-External tab.
- Thu Mar 14, 2024 12:38
- Forum: Technical Support
- Topic: MCG Ultimate Config Question
- Replies: 10
- Views: 687
Re: MCG Ultimate Config Question
What version of BlackBox is used with GF MCGU? Show me the photo.
- Wed Mar 13, 2024 15:40
- Forum: Тех. поддержка
- Topic: Нелинейность отклика оси Y Gunfighter I
- Replies: 23
- Views: 1578
Re: Нелинейность отклика оси Y Gunfighter I
Сильно сомневаюсь, что найдется такая, но поищем.
- Wed Mar 13, 2024 10:52
- Forum: Manuals and Howtos
- Topic: STECS module not detected
- Replies: 7
- Views: 632
Re: STECS module not detected
Reset to factory state using the "Default" button in the configurator and re-do Auto-configuration with the corresponding button (appears next to the "Find&Show" button).
- Wed Mar 13, 2024 10:47
- Forum: Тех. поддержка
- Topic: THQ + FSM-GA Пстоянно горят зеленые светодиоды
- Replies: 1
- Views: 446
Re: THQ + FSM-GA Пстоянно горят зеленые светодиоды
Так это зависит от установки перемычки и в дефолтном состоянии это норма. Смотрите видео.
- Tue Mar 12, 2024 13:15
- Forum: Manuals and Howtos
- Topic: STECS module not detected
- Replies: 7
- Views: 632
Re: STECS module not detected
Click the Find&Show button and show a screenshot of the window. You can try updating the configurator and firmware from here.
- Mon Mar 11, 2024 23:41
- Forum: Manuals and Howtos
- Topic: STECS module not detected
- Replies: 7
- Views: 632
Re: STECS module not detected
Show how you connected and a screenshot of the Global-External tab from the configurator.
- Mon Mar 11, 2024 23:38
- Forum: Technical Support
- Topic: VKB T-Rudders issue
- Replies: 4
- Views: 640
Re: VKB T-Rudders issue
The minimum recommended firmware version for this configurator is indicated in brackets. Higher is possible, lower is not. The numbers 255,255 indicate that the pedal axle is not calibrated. And without this, adequate operation of the axis should not be expected. I advise you to update the firmware ...
- Mon Mar 11, 2024 10:33
- Forum: Technical Support
- Topic: VKB T-Rudders issue
- Replies: 4
- Views: 640
Re: VKB T-Rudders issue
Show the Profile-Axes tab from the configurator.