Search found 3273 matches
- Wed Mar 20, 2024 14:47
- Forum: Тех. поддержка
- Topic: Нелинейность отклика оси Y Gunfighter I
- Replies: 23
- Views: 1081
Re: Нелинейность отклика оси Y Gunfighter I
Я выставил отверстия во фрикционном диске в горизонт, как на большинстве фото, Т.е. все-таки нарушили заводскую сборку узла? А ведь можно было только магнит повернуть, предварительно достав его. Иголкой можно было выяснить его существующее положение и от него и отталкиваться для поворота. GF4.JPEG
- Sun Mar 17, 2024 0:14
- Forum: Тех. поддержка
- Topic: Нелинейность отклика оси Y Gunfighter I
- Replies: 23
- Views: 1081
Re: Нелинейность отклика оси Y Gunfighter I
Стоп-стоп, не нужно нарушать заводскую сборку этого узла , если он не имеет люфта относительно штока.
- Sat Mar 16, 2024 23:55
- Forum: Тех. поддержка
- Topic: Нелинейность отклика оси Y Gunfighter I
- Replies: 23
- Views: 1081
Re: Нелинейность отклика оси Y Gunfighter I
Вывод после картинки - с вашим датчиком все в порядке, оба канала работают. Именно такая цель и стояла. Если уж так хочется ещё экспериментов, то можете попробовать повернуть магнит в разные стороны на 45-90 градусов. Естественно, при каждом новом положении делать калибровку заново. Не забудьте верн...
- Sat Mar 16, 2024 23:36
- Forum: Тех. поддержка
- Topic: Нелинейность отклика оси Y Gunfighter I
- Replies: 23
- Views: 1081
Re: Нелинейность отклика оси Y Gunfighter I
Внимательнее нужно копировать настройки. МPL не спроста снижен до 7 (хотя это может быть и другая цифра на другом экземпляре).
- Sat Mar 16, 2024 20:34
- Forum: Manuals and Howtos
- Topic: Need help with macros
- Replies: 3
- Views: 326
Re: Need help with macros
This is Alex_Oz, send all your thanks.
- Sat Mar 16, 2024 12:41
- Forum: Technical Support
- Topic: hardwiring a module to left side OTA stick
- Replies: 1
- Views: 262
Re: hardwiring a module to left side OTA stick
There are inscriptions near the connector that will help you figure out how to connect the connector. In 4 pins you can connect 3 pins, Shield (Sh) will remain free.
- Sat Mar 16, 2024 12:32
- Forum: Тех. поддержка
- Topic: Нелинейность отклика оси Y Gunfighter I
- Replies: 23
- Views: 1081
Re: Нелинейность отклика оси Y Gunfighter I
Настроить нужно вот так на неоткалиброванных (отказаться от неё) и показать скриншот из JoyTester:
- Fri Mar 15, 2024 17:29
- Forum: Тех. поддержка
- Topic: Нелинейность отклика оси Y Gunfighter I
- Replies: 23
- Views: 1081
Re: Нелинейность отклика оси Y Gunfighter I
Проверку работы каналов датчика по совету Alex_Oz делали, результаты есть?
- Fri Mar 15, 2024 15:32
- Forum: Manuals and Howtos
- Topic: Need help with macros
- Replies: 3
- Views: 326
Re: Need help with macros
You have a little confusion in understanding the macro number and timing, but this can be easily corrected by looking at the picture. Let me explain that you can only run the second macro of 4 buttons, you just need to assign a button to it. As well as only the 5th of the two. Try lowering it from 5...
- Fri Mar 15, 2024 12:21
- Forum: Technical Support
- Topic: Twist Adapter for Gunfighter IV MCG Pro Grip question
- Replies: 1
- Views: 257
Re: Twist Adapter for Gunfighter IV MCG Pro Grip question
You can use an old plastic 3-pin connector. Make a 3 pin out of a 4 pin one. The white one can be attached to the spring.
- Fri Mar 15, 2024 9:25
- Forum: Technical Support
- Topic: MCG Ultimate Config Question
- Replies: 10
- Views: 434
Re: MCG Ultimate Config Question
That is great.
- Fri Mar 15, 2024 0:05
- Forum: Technical Support
- Topic: MCG Ultimate Config Question
- Replies: 10
- Views: 434
Re: MCG Ultimate Config Question
Change 11 to 7, write it to the controller with the Set button and it should work.
If it doesn’t work, reset it to default on the new firmware (2.17E) and try to calibrate again.
If it doesn’t work, reset it to default on the new firmware (2.17E) and try to calibrate again.
- Thu Mar 14, 2024 22:04
- Forum: Technical Support
- Topic: MCG Ultimate Config Question
- Replies: 10
- Views: 434
Re: MCG Ultimate Config Question
Select the pedals and take a screenshot. And show the Profile-Axes tab.
Try updating the firmware and configurator from here.
Try updating the firmware and configurator from here.
- Thu Mar 14, 2024 20:44
- Forum: Technical Support
- Topic: MCG Ultimate Config Question
- Replies: 10
- Views: 434
Re: MCG Ultimate Config Question
With pedals connected to BlackBox GF, reset them to default using the button in the configurator and show a screenshot of the Global-External tab.
- Thu Mar 14, 2024 12:38
- Forum: Technical Support
- Topic: MCG Ultimate Config Question
- Replies: 10
- Views: 434
Re: MCG Ultimate Config Question
What version of BlackBox is used with GF MCGU? Show me the photo.