VKB-SIM

... of switching to negative once it reaches 0. I have it centered and the springs are the default ones. Thank you to anyone who could help. Cheers!

... recommended to more experienced users. Then, I suggest to add up to the springs on both bases, as the default springs, the 20s, are more of a holder rather than a recommended setup. Here's a guide ...

... Gladiator, this is an even higher level. Adjusting the tension of the springs and dumper is a bit tricky because you need to remove the rubber ... am and how much easier it is to maneuver. Feedback is great. I left the default CAMs and #20 springs and tightened the springs a bit and loosened ...

The single #20 spring per cam, which is the default setup, is certainly pretty weak and it's more like a holder rather than a recommended setup. I suggest trying a double #30 springs setup on each cam. This is the guide you'd need. I suggest not to swap the cams, ...

... loosened. I’ll have to experiment with it some more, I guess. Maybe the default springs aren’t strong enough? I figured they’d be fine for an SCG with no extension, so I didn’t ...

... would like to know what other combat simmers are doing with their cams, springs, cluutch settings etc. My present setup and configuration just doesn't ... difficult to control in a sraight line when attacking enemy. . Are the default installed cams the ones to go with? Are there other adjusments ...

... per cam? Single would be too light for the extension. Add up more springs, so you'll have 1x50 and at least a 1x20 per cam, release the dampeners completely, reset to default and calibrate, then do the test again. Here's a guide on adjusting the base, you ...

Select the device in VKBDevCfg, then press the Default button under the Tools tab. After restart click Yes for the configure popup. ... make sure the grip is at the middle of pitch axis (Y) , even if you have no springs on that axis. The whole process here .

... hard cams. For a precise return to center hard cams are recommended; Springs - there are 5 sets of springs and each cam could load 2 springs; ... to center the dry clutch has to be completely released; Deadzone - by default it comes set up to 0.5. I could be easily increased to 1.5-2 without ...

... which is mechanical in nature. However, I could not find anything. The springs are fine, no screw or so that blocks. I have then carried out the ... stick by running in program: VKBDevCfg-C.exe and doing "Default" - Start Calibr (move axes) - End Calibr. It remains with the ...

... ago, I took my MCG Ultimate stick off my Gunfighter base to change the springs. When I put the base back together and the controller back on the ... the stick needed to be calibrated. I clicked ok. I then clicked the default button under the tools tab and the stick restarted. I clicked the ...

decided to upgrade the springs in my GF III to No 50. All went well , disassembled re assembled and now have ... times , now on latest 2.122 firmware 2. i have tried recalibrating and setting to default including reboots of PC 3. i swapped out the black box, Mark 2 for the one is ...

Flying the Huey in DCS and Bell 47 in XPlane 11, I use default springs on the Evo and clutches adjusted to a tightness that allows a slow return to center,
works a charm for me.

I just changed the springs & adjusted the dampers on my Gunfighter mk2 with MCG Pro & now I'm having ... the axis when I move the stick. I also, tried flashing & then pressing on "default" before trying to calibrate, but there is still no motion on the bar graphs ...

... with a new gunfighter mk3. Immediately installed Space-S cams and 2x 20 Springs. I used VKB's video for reference. It notes to be careful about washers/cam ... there that doesn't go away even with screw tension. For record, the default setting that I've used (it came this way): nut > washer > bearing?/housing ...