Search found 12 matches
- Thu Nov 23, 2023 8:42
- Forum: Technical Support
- Topic: GF II / MCG pro en X-axis lag
- Replies: 10
- Views: 4134
Re: GF II / MCG pro en X-axis lag
Hi I took the unit to parts and reconnected every wire. I even took it further apart to check for any possible physical damage. I could not see there would have been anything wrong anywhere. Yet the problem persist. Pictures attached. I also noticed, the the Y-axis bearings are shot. Are they just p...
- Wed Nov 22, 2023 20:14
- Forum: Technical Support
- Topic: GF II / MCG pro en X-axis lag
- Replies: 10
- Views: 4134
Re: GF II / MCG pro en X-axis lag
After soldering the both contact surfaces, taking the unit down to bare minimums (removed springs, and grip), connected the unit to pc, there was no or almost no errors in the external errorlog. However, the lag remained and was now also present in Y axis. I installed the grip back, and tried again,...
- Wed Nov 22, 2023 19:11
- Forum: Technical Support
- Topic: GF II / MCG pro en X-axis lag
- Replies: 10
- Views: 4134
Re: GF II / MCG pro en X-axis lag
It seems, that some kind of contact issue somewhere is the fault here. I soldered a small amount of tin to the scratches. For a moment the joystick seemed to work like a charm, until the contact broke entirely. Now I start to search for the actual place of bad contact.
- Mon Nov 20, 2023 23:18
- Forum: Technical Support
- Topic: GF II / MCG pro en X-axis lag
- Replies: 10
- Views: 4134
Re: GF II / MCG pro en X-axis lag
Now my English fails me and I do not understand, what you mean by connecting the connectors to base itself?
- Mon Nov 20, 2023 22:01
- Forum: Technical Support
- Topic: GF II / MCG pro en X-axis lag
- Replies: 10
- Views: 4134
Re: GF II / MCG pro en X-axis lag
Hi Thank you for the extremely fast response! Excellent customer service! I am unable to find anything wrong with the wiring inside. I disconnected and connected everything just before posting the original post. However, there are grooves on the contacts between base and extension & extension an...
- Mon Nov 20, 2023 20:00
- Forum: Technical Support
- Topic: GF II / MCG pro en X-axis lag
- Replies: 10
- Views: 4134
GF II / MCG pro en X-axis lag
Hey! I have had my GF II for about 5 years. Bought it second hand. It started slowly generating problems: - Need of re-calibration quite often - Spikes on X-axis near full bank to right - Lag on X-axis left side Now it developed to state unbearable and unplayable. What I have done: - tried on differ...
- Wed Mar 13, 2019 20:22
- Forum: VKB FSC Europe
- Topic: December'18 batch
- Replies: 54
- Views: 31844
Re: December'18 batch
While I agree that VKB is not doing everything as good as they could, being a melodramatic kid aint helping noone, expect the individuals, who will get the stuff you had preordered.
- Thu Feb 28, 2019 18:18
- Forum: VKB FSC Europe
- Topic: December'18 batch
- Replies: 54
- Views: 31844
Re: December'18 batch
The cargo contains only GF MCG Pro EN variants, T-Rudder pedals and stick extension kits. Unfortunately it should fulfill roughly half of the pre-orders. Another half is currently being produced and I believe it could be shipped to us in a week or two. Does this mean, that I, who haven't even had t...
- Sat Oct 06, 2018 10:25
- Forum: Technical Support
- Topic: VKBDevCFG dying on me [SOLVED]
- Replies: 7
- Views: 3777
Re: VKBDevCFG dying on me [SOLVED]
It's quite peculiar thing to happen to be honest. Windows shouldn't allow software to get outside of the screens ...
However, what gave it a way was, that when I alt+tabbed, I saw the VKBDevCfg program open and running on the thumbnails. Thus I knew, it is running for reals.
However, what gave it a way was, that when I alt+tabbed, I saw the VKBDevCfg program open and running on the thumbnails. Thus I knew, it is running for reals.
- Fri Oct 05, 2018 23:52
- Forum: Technical Support
- Topic: VKBDevCFG dying on me [SOLVED]
- Replies: 7
- Views: 3777
Re: VKBDevCFG dying on me
Nope. Both unsuccessful.
edit.: Solved!
Issue was, the window had jumped outside of my screens for some reason. So the program worked, but the window was outside of my screens.
edit.: Solved!
Issue was, the window had jumped outside of my screens for some reason. So the program worked, but the window was outside of my screens.
- Fri Oct 05, 2018 11:22
- Forum: Technical Support
- Topic: VKBDevCFG dying on me [SOLVED]
- Replies: 7
- Views: 3777
Re: VKBDevCFG dying on me
The base and grip works perfectly as far as I can tell. I downloaded the the VKBDevCfg from your websites and I picked the latest dated version of it (can check the number once back home). edit. I did use the VKBDevCfg for few times and it worked well without any problems. Only after I used the butt...
- Fri Oct 05, 2018 9:47
- Forum: Technical Support
- Topic: VKBDevCFG dying on me [SOLVED]
- Replies: 7
- Views: 3777
VKBDevCFG dying on me [SOLVED]
Hi I reacently got me a Gunfighter mk II rev. B base with KG12 grip second handed. Now, as I started to try to learn the VKBDevCFG software, it suddenly died on me. What I did: - I had calibrated my stick - I tried to start to make a profile for pinky button shift function with the manual's guidance...