That's right, that unit will have to stay on the desk.
Show us a pic with your setup, OP, so we can see if you can integrate the 2 modules into the UCM; for example, if you have 2 UCMs you can get a module on each, so you won't need the MFH anymore.
Search found 5221 matches
- Mon May 20, 2024 21:03
- Forum: General discussions
- Topic: I am an idiot - need help!
- Replies: 3
- Views: 84
- Mon May 20, 2024 20:58
- Forum: Technical Support
- Topic: how often calibrate the device
- Replies: 2
- Views: 98
Re: how often calibrate the device
Please post a screenshot of Profile/Axes/Logical and Physical Axes chart.
- Mon May 20, 2024 9:35
- Forum: Technical Support
- Topic: STECS Thumbwheel Axis Issue
- Replies: 3
- Views: 119
Re: STECS Thumbwheel Axis Issue
This is a completely unrelated issue, most probably an uncalibrated device.
- Mon May 20, 2024 9:33
- Forum: General discussions
- Topic: I am an idiot - need help!
- Replies: 3
- Views: 84
Re: I am an idiot - need help!
So, if you want to run the SEM and FSM as an independent unit you'll need the following: - SEM, FSM-GA, MFH (you already got these); - JST to USB C cable ; - GNX HID Controller . You'll install the GNX HID Controller into the SEM, connect the SEM to the FSM by the JST to USB C cable (JST to SEM, USB...
- Sat May 18, 2024 20:06
- Forum: VKB FSC Europe
- Topic: when is support typically available?
- Replies: 2
- Views: 95
Re: when is support typically available?
Contacting the vendor by email or from the contact page on their website is the way.
- Fri May 17, 2024 21:10
- Forum: Technical Support
- Topic: STECS Thumbwheel Axis Issue
- Replies: 3
- Views: 119
Re: STECS Thumbwheel Axis Issue
If the throttle is properly calibrated and the axis still acts like that please fill up a service ticket.
- Fri May 17, 2024 11:02
- Forum: Technical Support
- Topic: NXT Evo does not connect when FSM-GA is connected to GNX-SEM, but connects when FSM-GA is connected to GNX-THQ
- Replies: 4
- Views: 138
Re: NXT Evo does not connect when FSM-GA is connected to GNX-SEM, but connects when FSM-GA is connected to GNX-THQ
Please update to the latest software and firmware, then reset to default and click Yes for the config button. If still not working afterwards fill up a service ticket with your local vendor.
- Tue May 14, 2024 10:41
- Forum: Technical Support
- Topic: Device Descriptor Request Failed
- Replies: 1
- Views: 82
Re: Device Descriptor Request Failed
I think we already responded to this on the tickets; if not, please fill up a ticket with the issue.
- Tue May 14, 2024 10:40
- Forum: Technical Support
- Topic: SEM issue
- Replies: 3
- Views: 100
Re: SEM issue
Maybe the cable is bad, do you have another cable to try?
Also try swapping USB ports too.
Also try swapping USB ports too.
- Tue May 14, 2024 10:32
- Forum: Technical Support
- Topic: NXT Evo does not connect when FSM-GA is connected to GNX-SEM, but connects when FSM-GA is connected to GNX-THQ
- Replies: 4
- Views: 138
Re: NXT Evo does not connect when FSM-GA is connected to GNX-SEM, but connects when FSM-GA is connected to GNX-THQ
Can you post a pic with your setup please?
- Tue May 14, 2024 10:30
- Forum: Technical Support
- Topic: Missing detents for STECS in VKBDevConfig
- Replies: 1
- Views: 54
Re: Missing detents for STECS in VKBDevConfig
Just close and run again VKBDevCfg, that should fix it.
- Fri May 10, 2024 21:15
- Forum: Technical Support
- Topic: SOLVED: STECs spamming multiple control presses in MSFS 2020
- Replies: 2
- Views: 140
Re: SOLVED: STECs spamming multiple control presses in MSFS 2020
Thanks for the update.
- Fri May 10, 2024 21:15
- Forum: Technical Support
- Topic: Could rig vibrations be harmful to VKB Stecs/Gladiator?
- Replies: 1
- Views: 89
Re: Could rig vibrations be harmful to VKB Stecs/Gladiator?
Any electronic device might get damaged if it's under permanent vibrations; now it depends how hard it's vibrating and other factors, but probably you'll be fine. I suggest though to put a sheet of rubber between the throttle and mount plate, to act like a buffer.
Nice setup btw
Nice setup btw
- Fri May 10, 2024 21:10
- Forum: Technical Support
- Topic: NXT Evo R X axis sticking
- Replies: 3
- Views: 119
Re: NXT Evo R X axis sticking
Fully release the dampeners and make sure the gimbal is moving freely https://youtu.be/HRC5uPpFPzk
- Tue May 07, 2024 2:05
- Forum: Technical Support
- Topic: Gunfighter IV SCG malfunction
- Replies: 9
- Views: 262
Re: Gunfighter IV SCG malfunction
Please download the attached file, then extract it in the same folder with zBootloader. Run zBootloader as Admin, make sure the BBIII is in bootloading mode (disconnect other devices to make sure), then erase everything from the command line and type in: load . Try to flash the Unified firmware afte...