Search found 5217 matches
- Sat May 18, 2024 20:06
- Forum: VKB FSC Europe
- Topic: when is support typically available?
- Replies: 1
- Views: 31
Re: when is support typically available?
Contacting the vendor by email or from the contact page on their website is the way.
- Fri May 17, 2024 21:10
- Forum: Technical Support
- Topic: STECS Thumbwheel Axis Issue
- Replies: 1
- Views: 63
Re: STECS Thumbwheel Axis Issue
If the throttle is properly calibrated and the axis still acts like that please fill up a service ticket.
- Fri May 17, 2024 11:02
- Forum: Technical Support
- Topic: NXT Evo does not connect when FSM-GA is connected to GNX-SEM, but connects when FSM-GA is connected to GNX-THQ
- Replies: 4
- Views: 117
Re: NXT Evo does not connect when FSM-GA is connected to GNX-SEM, but connects when FSM-GA is connected to GNX-THQ
Please update to the latest software and firmware, then reset to default and click Yes for the config button. If still not working afterwards fill up a service ticket with your local vendor.
- Tue May 14, 2024 10:41
- Forum: Technical Support
- Topic: Device Descriptor Request Failed
- Replies: 1
- Views: 80
Re: Device Descriptor Request Failed
I think we already responded to this on the tickets; if not, please fill up a ticket with the issue.
- Tue May 14, 2024 10:40
- Forum: Technical Support
- Topic: SEM issue
- Replies: 3
- Views: 93
Re: SEM issue
Maybe the cable is bad, do you have another cable to try?
Also try swapping USB ports too.
Also try swapping USB ports too.
- Tue May 14, 2024 10:32
- Forum: Technical Support
- Topic: NXT Evo does not connect when FSM-GA is connected to GNX-SEM, but connects when FSM-GA is connected to GNX-THQ
- Replies: 4
- Views: 117
Re: NXT Evo does not connect when FSM-GA is connected to GNX-SEM, but connects when FSM-GA is connected to GNX-THQ
Can you post a pic with your setup please?
- Tue May 14, 2024 10:30
- Forum: Technical Support
- Topic: Missing detents for STECS in VKBDevConfig
- Replies: 1
- Views: 50
Re: Missing detents for STECS in VKBDevConfig
Just close and run again VKBDevCfg, that should fix it.
- Fri May 10, 2024 21:15
- Forum: Technical Support
- Topic: SOLVED: STECs spamming multiple control presses in MSFS 2020
- Replies: 2
- Views: 128
Re: SOLVED: STECs spamming multiple control presses in MSFS 2020
Thanks for the update.
- Fri May 10, 2024 21:15
- Forum: Technical Support
- Topic: Could rig vibrations be harmful to VKB Stecs/Gladiator?
- Replies: 1
- Views: 86
Re: Could rig vibrations be harmful to VKB Stecs/Gladiator?
Any electronic device might get damaged if it's under permanent vibrations; now it depends how hard it's vibrating and other factors, but probably you'll be fine. I suggest though to put a sheet of rubber between the throttle and mount plate, to act like a buffer.
Nice setup btw
Nice setup btw
- Fri May 10, 2024 21:10
- Forum: Technical Support
- Topic: NXT Evo R X axis sticking
- Replies: 3
- Views: 109
Re: NXT Evo R X axis sticking
Fully release the dampeners and make sure the gimbal is moving freely https://youtu.be/HRC5uPpFPzk
- Tue May 07, 2024 2:05
- Forum: Technical Support
- Topic: Gunfighter IV SCG malfunction
- Replies: 9
- Views: 247
Re: Gunfighter IV SCG malfunction
Please download the attached file, then extract it in the same folder with zBootloader. Run zBootloader as Admin, make sure the BBIII is in bootloading mode (disconnect other devices to make sure), then erase everything from the command line and type in: load . Try to flash the Unified firmware afte...
- Tue May 07, 2024 1:59
- Forum: VKB FSC Europe
- Topic: Modern combat grip ultimate
- Replies: 6
- Views: 750
Re: Modern combat grip ultimate
The ETA for the MCGU is mid to end of May. Please mention in the order notes that you need it with RevB connector.
- Mon May 06, 2024 3:57
- Forum: Technical Support
- Topic: Gunfighter IV SCG malfunction
- Replies: 9
- Views: 247
Re: Gunfighter IV SCG malfunction
With the BB in the same stage as in your screenshot above (bootloading mode, with blue light and OK for Boot Device) clear the command line (where the firmware name is) and type: save . Check the folder where zbootloader is stored, zip the .op1 file you'll find in there and attach it to a message he...
- Mon May 06, 2024 3:53
- Forum: VKB FSC Europe
- Topic: Price change with location in UK
- Replies: 10
- Views: 1635
Re: Price change with location in UK
If you've been charged once for VAT surely you won't get charged a second time, just keep the invoice handy for delivery as proof.
- Mon May 06, 2024 3:49
- Forum: Official announcements
- Topic: Gunfighter IV Upgrade Kit
- Replies: 10
- Views: 15243
Re: Gunfighter IV Upgrade Kit
Trying to include the GFII too, but can't confirm at this time, sorry.