Search found 22 matches
- Sun Apr 10, 2022 20:35
- Forum: Technical Support
- Topic: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
- Replies: 31
- Views: 34047
Re: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
Alright, so a couple of weeks with the upgraded electronics - everything working perfectly now (no drift, perfect center all the time). Will update here if anything changes.
- Fri Mar 18, 2022 14:26
- Forum: Technical Support
- Topic: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
- Replies: 31
- Views: 34047
Re: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
Thank you fallout9! I ended up submitting a support ticket for confirmation. Support seemed clear on this being a connector issue due to the design of the first batch of the model (I managed to coincidentally snag a order apx. 5 minutes after release, for good or bad... Mostly good! :D ). The PCB an...
- Thu Feb 17, 2022 20:59
- Forum: Technical Support
- Topic: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
- Replies: 31
- Views: 34047
Re: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
Unfortunately, the same problem is back again. Random twitching and x axis center getting slightly offset from time to time: Twitching X-axis and offset center 2022-02-17.PNG Updated to latest VKB firmware (XT2 v2.099), but no improvement. The tiny movement and occasional random offset seems to be v...
- Thu Jan 20, 2022 10:21
- Forum: Technical Support
- Topic: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
- Replies: 31
- Views: 34047
Re: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
Since I previously posted here, just going back for an update: I've had continued X axis twitching going on, on and off since last posting. For some period it was less, then it was more, then less again. I found this thread on another forum that finally gave me a hint: https://forums.mudspike.com/t/...
- Sat May 02, 2020 15:31
- Forum: Technical Support
- Topic: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
- Replies: 31
- Views: 34047
Re: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
To follow-up on my previous post; took the base apart again, including removing the x-axis sensor board. Cleaned the surface under, replaced the tape, unplugged the senor board cable and reversed direction of the cable. Made sure to route it free from the board when reassembling it. I gather from th...
- Thu Apr 30, 2020 16:06
- Forum: Technical Support
- Topic: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
- Replies: 31
- Views: 34047
Re: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
And here's screenshot from vkbdevcfg.
- Thu Apr 30, 2020 16:03
- Forum: Technical Support
- Topic: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
- Replies: 31
- Views: 34047
Re: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
And another screenshot immediately after my previous post, where I thought the issue had gone away (these are all full X deflections left and right, note that it doesn't even reach max on one occasion).
- Thu Apr 30, 2020 16:00
- Forum: Technical Support
- Topic: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
- Replies: 31
- Views: 34047
Re: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
Same issue here. I've cleaned the insides of the base, loaded every new firmware as they are released. But the issue remains. It's normally only/mostly observed as I first start the computer for the day. After a couple of full joystick deflections it gets better, often not noticed again until the ne...
- Fri Mar 06, 2020 20:33
- Forum: Technical Support
- Topic: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
- Replies: 31
- Views: 34047
Re: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
Quick update on my own cleaning; could see a small piece of debris stuck between the sensor and the magnet on the x-axis. Used my Super Blower (https://www.amazon.com/dp/B0046UJFAG?tag=duckduckgo-ffab-20&linkCode=osi&th=1&psc=1) to dislodge it. This unfortunately meant I didn't get any p...
- Fri Mar 06, 2020 20:06
- Forum: Technical Support
- Topic: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
- Replies: 31
- Views: 34047
Re: Gunfighter mk.II - MCG Pro grip - X axis twitching problem
I have the exact same issue; X-axis is acting up randomly. Re-clibrating and fiddling a bit, then it works fine for a couple of hours, then issues again. Seeing similar symptoms on y-axis, but not even close to the same frequency and amount of issues. Definitely some "spikyness" in the gra...
- Mon Nov 05, 2018 9:08
- Forum: Technical Support
- Topic: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
- Replies: 21
- Views: 11105
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
Couldn't fix the X axis random displacement through VKBDevCfg. I could fix it temporarily by re-calibrating or manually adjusting Bias. However, within 5 minutes it would drift off a couple of hundred points again (try flying the MIG29S with that... :lol: ). Disassembled the base and re-connected al...
- Sat Sep 29, 2018 19:04
- Forum: Technical Support
- Topic: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
- Replies: 21
- Views: 11105
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
Something I've noticed a few days ago, which might relate to this. The whole MCG Pro trigger becomes "unstable" with safe/armed being mixed up or fire1/2 buttons non-functioning after you re-run calibration. I did it a few times (using all axis or just x/y) until it just started working. ...
- Sat Sep 29, 2018 19:01
- Forum: Technical Support
- Topic: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
- Replies: 21
- Views: 11105
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
Working now: VKBDevCfg-C_v0.88.71 and _BlackBox_GF_MCG_PRO_v1_95_4.
Thank you!
Thank you!
- Wed Sep 26, 2018 10:38
- Forum: Technical Support
- Topic: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
- Replies: 21
- Views: 11105
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
Tested again with firmware _BlackBox_GF_MCG_PRO_v1_95_3.vkb and VKBDevCfg-C_v0.88.66 - not working.
- Fri Sep 21, 2018 0:12
- Forum: Technical Support
- Topic: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
- Replies: 21
- Views: 11105
Re: MCG Pro Trigger A2B misfuntion after setting X/Y axis response curve
CARTOK wrote:Tested v1_95_2 (along with vkbdevcfg 0.88.45):
Some changes; The A2B buttons for the trigger are all on by default now (rather than previous off), but not reacting to any axis movement.
Edit: Referenced the wrong firmware version.
This was the result. Not working.