Search found 26 matches
- Fri Nov 06, 2020 18:41
- Forum: Manuals and Howtos
- Topic: Blackbox manual ?
- Replies: 5
- Views: 3565
Re: Blackbox manual ?
All I've seen is this picture which describes the LED number in VKBConfig? AFAIK, the leds just tell you if something is connected. But you can also program the LEDs to change based on shift state..etc Someone who has a better understanding will have to reply. I barely understand any of the VKBConfi...
- Sun Aug 23, 2020 10:03
- Forum: Manuals and Howtos
- Topic: SHIFT Button with two joystick setup
- Replies: 7
- Views: 4021
Re: SHIFT Button with two joystick setup
OK, I worked out what the issue was.
If you have Partial Write ticked, even if you select all the options, it appears that it won't be able to write the firmware for this particular part.
Removing Partial Write allowed it to write the firmware correct.
If you have Partial Write ticked, even if you select all the options, it appears that it won't be able to write the firmware for this particular part.
Removing Partial Write allowed it to write the firmware correct.
- Fri Aug 21, 2020 12:15
- Forum: Manuals and Howtos
- Topic: SHIFT Button with two joystick setup
- Replies: 7
- Views: 4021
Re: SHIFT Button with two joystick setup
Hi Victorus I tried as you suggested, but it is still not working. It sets the changes, but ignores the Global Shift change which remains unticked. Could it be the version of VKBDevCfg or the stick firmware? Also, do you know what the yellow light is in Zlink? I was looking through some of the .ru l...
- Thu Aug 20, 2020 10:14
- Forum: Manuals and Howtos
- Topic: SHIFT Button with two joystick setup
- Replies: 7
- Views: 4021
Re: SHIFT Button with two joystick setup
I can't seem to set after selecting the Slave and ticking the box for Global Shifts. A message comes up saying there is no new data to set and to box remains unticked.
- Sat Jun 20, 2020 0:15
- Forum: Technical Support
- Topic: Rubber wrist wrest coming off?
- Replies: 4
- Views: 2444
Re: Rubber wrist wrest coming off?
Yep. Happened to my mouse. No big issue
- Fri Jun 19, 2020 3:02
- Forum: Technical Support
- Topic: Rubber wrist wrest coming off?
- Replies: 4
- Views: 2444
Re: Rubber wrist wrest coming off?
Now that you mention it, I have just noticed the rubber part becoming a bit sticky. I'll try giving it a wipe to see if it goes away.
- Mon Jun 01, 2020 13:02
- Forum: Technical Support
- Topic: Shift0,1,2 modifier
- Replies: 6
- Views: 5347
Re: Shift0,1,2 modifier
Sure. This one is pretty straight forward and I'm always looking to see what cool stuff people do. Most of the VKB PDF guide I struggle to make sense of - I wish it was better written with examples :lol: This is what I've done for my SCG-L. This is the Red button on my SCG-L (highlighted in the red ...
- Thu May 28, 2020 13:37
- Forum: General discussions
- Topic: Mk.III chipped PCB corner - safe to install?
- Replies: 3
- Views: 6724
Re: Mk.III chipped PCB corner - safe to install?
I've got 2 upgrade kits and both PCBs were like that too.
No issues with the install (mk.1 to mk.3) other than one of the screws for the PCB bumping into the top plate when installed. I just omitted it.
No issues with the install (mk.1 to mk.3) other than one of the screws for the PCB bumping into the top plate when installed. I just omitted it.
- Mon May 25, 2020 23:04
- Forum: Technical Support
- Topic: Kosmosima GF II Blue/Red grip LED's turn off and reset.
- Replies: 17
- Views: 12657
Re: Kosmosima GF II Blue/Red grip LED's turn off and reset.
Sorry to bump an old thread. I am having a similar issue. 1 - VKB SCG Premium-L (3-pin Rev.A) & Gunfighter Mk.1 upgraded to Mk.3 2 - Controller Firmware version v1.98F 3 - 20 Springs on both 4 - Space-H on both 5 - VKBDevCfg v0.91.22 I've tried reseating the grip to make sure it is 100% connecte...
- Mon May 25, 2020 10:38
- Forum: Technical Support
- Topic: Shift0,1,2 modifier
- Replies: 6
- Views: 5347
Re: Shift0,1,2 modifier
Yep - I worked that out.
I've been reading through the guide. It is slowly making some sense to me. Also - alot of trial and error
I've been reading through the guide. It is slowly making some sense to me. Also - alot of trial and error
- Mon May 25, 2020 5:21
- Forum: Technical Support
- Topic: Some MkI to MkIII issues
- Replies: 19
- Views: 26561
Re: Some MkI to MkIII issues
I did the upgrade for two of my GF MK1s and ran into this issue.
I ended up just not installing the screw that bumps into the top plate.
The PCB seems secure enough with the single screw and there isn't really anything to cause the PCB to move.
I ended up just not installing the screw that bumps into the top plate.
The PCB seems secure enough with the single screw and there isn't really anything to cause the PCB to move.
- Sun May 24, 2020 16:45
- Forum: Technical Support
- Topic: Shift0,1,2 modifier
- Replies: 6
- Views: 5347
Re: Shift0,1,2 modifier
Ok, I worked it out.
I don't know what I was doing before, but it's super simple. Just mark the checkboxes use Shift1,2 and assign button.
I don't know what I was doing before, but it's super simple. Just mark the checkboxes use Shift1,2 and assign button.
- Sun May 24, 2020 8:25
- Forum: Technical Support
- Topic: Shift0,1,2 modifier
- Replies: 6
- Views: 5347
Shift0,1,2 modifier
I'm trying to create different layouts using the shift modifier, however it's not really working as intended. There are 3 modifier states (Shift0, 1, 2), but my modified button will work in Shift1 & 2. How do I create separate logical buttons on SHift1 and a different set on Shift2? I have the S...
- Sat May 23, 2020 10:42
- Forum: Technical Support
- Topic: Tempo, POV and Microstick Switch
- Replies: 2
- Views: 1736
Re: Tempo, POV and Microstick Switch
That worked perfectly fallout9, thank you.
- Sat May 23, 2020 4:14
- Forum: Technical Support
- Topic: Tempo, POV and Microstick Switch
- Replies: 2
- Views: 1736
Tempo, POV and Microstick Switch
On my MCG Pro, I have the Gate Cont Hat by default controlling POV 2. For the mapping, I have it on microswitch switched by Tempo B. Microswitch.PNG This means that when I click the Hat, it will press button 8. If I hold the Hat for longer than Tempo Time, It will switch the Hat to Axis Slider 1 and...