Search found 3319 matches
- Fri Jul 26, 2024 0:02
- Forum: Manuals and Howtos
- Topic: Gladiator NXT/GNX WWII Throttle Combo Installation Manual
- Replies: 1
- Views: 50
Re: Gladiator NXT/GNX WWII Throttle Combo Installation Manual
Various videos here.
- Thu Jul 25, 2024 10:56
- Forum: Technical Support
- Topic: UCM Stronghold Mounting Adapter Plate for Gunfigther
- Replies: 5
- Views: 194
Re: UCM Stronghold Mounting Adapter Plate for Gunfigther
Longer ones do not exist and have not been produced. In your particular case, you can drill two additional holes to suit your preferred mounting angle. Approximately in this place, reassemble the bracket.
- Thu Jul 25, 2024 10:42
- Forum: General discussions
- Topic: Fat Black Mamba Upgrade Possible?
- Replies: 5
- Views: 220
Re: Fat Black Mamba Upgrade Possible?
My task was to completely abandon the 5-pin connector in order to use any grip with a 3-pin connector.
If you use only one grip and a non-removable one, then you can completely abandon the contact pair.
If you use only one grip and a non-removable one, then you can completely abandon the contact pair.
- Thu Jul 25, 2024 10:36
- Forum: Technical Support
- Topic: T.Rudder MkV not reaching full range
- Replies: 1
- Views: 55
Re: T.Rudder MkV not reaching full range
Show the Profile-Axes tab from the configurator.
- Wed Jul 24, 2024 14:16
- Forum: Technical Support
- Topic: UCM Stronghold Mounting Adapter Plate for Gunfigther
- Replies: 5
- Views: 194
Re: UCM Stronghold Mounting Adapter Plate for Gunfigther
Show me a photo of your plate so you can judge the size.
- Tue Jul 23, 2024 20:16
- Forum: General discussions
- Topic: Fat Black Mamba Upgrade Possible?
- Replies: 5
- Views: 220
Re: Fat Black Mamba Upgrade Possible?
If you have access to turning work, then there is nothing complicated. You need to grind out the adapter and replace the 5-pin one with a 3-pin one. Then connect and configure. I've been doing this kind of work for a long time.
- Fri Jul 19, 2024 13:59
- Forum: Technical Support
- Topic: MCGU buttons started to act unreliably
- Replies: 14
- Views: 415
Re: MCGU buttons started to act unreliably
You can run JoyTester in parallel with the configurator and observe both the communication monitor and the operation of buttons. There is nothing unusual in the video, this is in the order of things.
- Fri Jul 19, 2024 13:31
- Forum: Technical Support
- Topic: MCGU buttons started to act unreliably
- Replies: 14
- Views: 415
Re: MCGU buttons started to act unreliably
You can try moving the button response slider as far to the right as possible, maybe this will help. Namely, you can set the handle “on hot”, focusing on the readings of the communication monitor. The quality in the monitor should be, I would say, like green grass, constant, with acceptable “stumps ...
- Fri Jul 19, 2024 12:42
- Forum: Technical Support
- Topic: Is it possible to have this tool ?
- Replies: 3
- Views: 157
Re: Is it possible to have this tool ?
To download from the link there, you need to register there. I'll post the archive here. _Diagram1.zip Diagram.jpg When changing controls, you need to focus on their physical binding. In order not to load a newly created ini file to view the settings, you can save a picture (in jpg, for example) of ...
- Fri Jul 19, 2024 12:13
- Forum: Technical Support
- Topic: MCGU buttons started to act unreliably
- Replies: 14
- Views: 415
Re: MCGU buttons started to act unreliably
A few movements with a soldering iron (careful) can turn your slightly shabby pad into something almost new, like the one in my photo.
To understand why phantom button presses occur when the brake lever moves, you need to see the settings in the Profile-Axes, Profile-Axes-Axes2Buttons tabs.
To understand why phantom button presses occur when the brake lever moves, you need to see the settings in the Profile-Axes, Profile-Axes-Axes2Buttons tabs.
- Thu Jul 18, 2024 19:46
- Forum: Technical Support
- Topic: MCGU buttons started to act unreliably
- Replies: 14
- Views: 415
Re: MCGU buttons started to act unreliably
In the photo, the contact pad of the extension cord is out of focus, it is difficult to understand whether there are traces of spring contacts there, like on the base, or not.
- Thu Jul 18, 2024 17:51
- Forum: Technical Support
- Topic: Is it possible to have this tool ?
- Replies: 3
- Views: 157
Re: Is it possible to have this tool ?
This function is available from configurator version v_0.93.02 (and later). The inscriptions are made according to this template, I think there is nothing complicated.
- Thu Jul 18, 2024 13:42
- Forum: Technical Support
- Topic: MCGU buttons started to act unreliably
- Replies: 14
- Views: 415
Re: MCGU buttons started to act unreliably
This is what she looks like.
- Thu Jul 18, 2024 13:23
- Forum: Technical Support
- Topic: MCGU buttons started to act unreliably
- Replies: 14
- Views: 415
Re: MCGU buttons started to act unreliably
There should be no yellow, much less red, splashes when moving the grip. Show a photo of the contact pad (not the spring pad) on the base. It is worth checking the spring contacts in the grip so that they are not stuck. I advise you to install the grip in this sequence - with the window for monitori...
- Thu Jul 18, 2024 11:23
- Forum: Technical Support
- Topic: MCGU buttons started to act unreliably
- Replies: 14
- Views: 415
Re: MCGU buttons started to act unreliably
Show the Profile-Axes and Test-External Devices tabs. In the latter, you can evaluate the quality of connection between the handle and the base when moving by clicking on the handle image. These buttons are activated when you install a button module, but you have a mini stick.