Search found 3242 matches

by Ron61
Sun Mar 17, 2024 0:14
Forum: Тех. поддержка
Topic: Нелинейность отклика оси Y Gunfighter I
Replies: 18
Views: 403

Re: Нелинейность отклика оси Y Gunfighter I

Стоп-стоп, не нужно нарушать заводскую сборку этого узла , если он не имеет люфта относительно штока.
3-1.jpg
3_2.jpg
3_3.JPG
by Ron61
Sat Mar 16, 2024 23:55
Forum: Тех. поддержка
Topic: Нелинейность отклика оси Y Gunfighter I
Replies: 18
Views: 403

Re: Нелинейность отклика оси Y Gunfighter I

Вывод после картинки - с вашим датчиком все в порядке, оба канала работают. Именно такая цель и стояла. Если уж так хочется ещё экспериментов, то можете попробовать повернуть магнит в разные стороны на 45-90 градусов. Естественно, при каждом новом положении делать калибровку заново. Не забудьте верн...
by Ron61
Sat Mar 16, 2024 23:36
Forum: Тех. поддержка
Topic: Нелинейность отклика оси Y Gunfighter I
Replies: 18
Views: 403

Re: Нелинейность отклика оси Y Gunfighter I

Внимательнее нужно копировать настройки. МPL не спроста снижен до 7 (хотя это может быть и другая цифра на другом экземпляре).
by Ron61
Sat Mar 16, 2024 20:34
Forum: Manuals and Howtos
Topic: Need help with macros
Replies: 3
Views: 93

Re: Need help with macros

This is Alex_Oz, send all your thanks.
by Ron61
Sat Mar 16, 2024 12:41
Forum: Technical Support
Topic: hardwiring a module to left side OTA stick
Replies: 1
Views: 39

Re: hardwiring a module to left side OTA stick

There are inscriptions near the connector that will help you figure out how to connect the connector. In 4 pins you can connect 3 pins, Shield (Sh) will remain free.
by Ron61
Sat Mar 16, 2024 12:32
Forum: Тех. поддержка
Topic: Нелинейность отклика оси Y Gunfighter I
Replies: 18
Views: 403

Re: Нелинейность отклика оси Y Gunfighter I

Настроить нужно вот так на неоткалиброванных (отказаться от неё) и показать скриншот из JoyTester:
Y.jpg
Y_1.jpg
by Ron61
Fri Mar 15, 2024 17:29
Forum: Тех. поддержка
Topic: Нелинейность отклика оси Y Gunfighter I
Replies: 18
Views: 403

Re: Нелинейность отклика оси Y Gunfighter I

Проверку работы каналов датчика по совету Alex_Oz делали, результаты есть?
by Ron61
Fri Mar 15, 2024 15:32
Forum: Manuals and Howtos
Topic: Need help with macros
Replies: 3
Views: 93

Re: Need help with macros

You have a little confusion in understanding the macro number and timing, but this can be easily corrected by looking at the picture. Let me explain that you can only run the second macro of 4 buttons, you just need to assign a button to it. As well as only the 5th of the two. Try lowering it from 5...
by Ron61
Fri Mar 15, 2024 12:21
Forum: Technical Support
Topic: Twist Adapter for Gunfighter IV MCG Pro Grip question
Replies: 1
Views: 47

Re: Twist Adapter for Gunfighter IV MCG Pro Grip question

You can use an old plastic 3-pin connector. Make a 3 pin out of a 4 pin one. The white one can be attached to the spring.
by Ron61
Fri Mar 15, 2024 9:25
Forum: Technical Support
Topic: MCG Ultimate Config Question
Replies: 10
Views: 146

Re: MCG Ultimate Config Question

That is great.
by Ron61
Fri Mar 15, 2024 0:05
Forum: Technical Support
Topic: MCG Ultimate Config Question
Replies: 10
Views: 146

Re: MCG Ultimate Config Question

Change 11 to 7, write it to the controller with the Set button and it should work.
If it doesn’t work, reset it to default on the new firmware (2.17E) and try to calibrate again.
TRV_1.jpg
by Ron61
Thu Mar 14, 2024 22:04
Forum: Technical Support
Topic: MCG Ultimate Config Question
Replies: 10
Views: 146

Re: MCG Ultimate Config Question

Select the pedals and take a screenshot. And show the Profile-Axes tab.
Try updating the firmware and configurator from here.
TRV.jpg
by Ron61
Thu Mar 14, 2024 20:44
Forum: Technical Support
Topic: MCG Ultimate Config Question
Replies: 10
Views: 146

Re: MCG Ultimate Config Question

With pedals connected to BlackBox GF, reset them to default using the button in the configurator and show a screenshot of the Global-External tab.
by Ron61
Thu Mar 14, 2024 12:38
Forum: Technical Support
Topic: MCG Ultimate Config Question
Replies: 10
Views: 146

Re: MCG Ultimate Config Question

What version of BlackBox is used with GF MCGU? Show me the photo.
by Ron61
Wed Mar 13, 2024 15:40
Forum: Тех. поддержка
Topic: Нелинейность отклика оси Y Gunfighter I
Replies: 18
Views: 403

Re: Нелинейность отклика оси Y Gunfighter I

Сильно сомневаюсь, что найдется такая, но поищем.

Go to advanced search