So how many buttons are not responding? I only see one 8th worked. Where are the others?How many red squares light up when you move the HAT completely in the Profile-Buttons?
Show the configurator window in full, without clipping.
Search found 3284 matches
- Sat Oct 16, 2021 10:32
- Forum: VKB FSC Europe
- Topic: Ticket #6044
- Replies: 26
- Views: 7117
- Thu Oct 14, 2021 22:08
- Forum: Программное обеспечение
- Topic: Gladiator mkii смена осей при смене mode?
- Replies: 13
- Views: 8562
Re: Gladiator mkii смена осей при смене mode?
Раз твиста нет на 3й оси, отключаем в Global-External Devices её - ставим вместо М-MarsX,Y None. Педалей, как я понимаю, тоже нет - отключаем несуществующие оси 6,7,8 в Profile-Axes сняв галки En, Vs. Делаем джампер на кнопку Shift, как на картинке. JMP.jpg На 36й делаем переключатель на 3тью ось по...
- Thu Oct 14, 2021 18:55
- Forum: Technical Support
- Topic: Gladiator NXT A3 Button switches
- Replies: 2
- Views: 876
Re: Gladiator NXT A3 Button switches
Activate the Poll checkbox in the Profile-Buttons tab and check all the buttons on this HAT. Red squares should light up in all HAT positions.
If this does not happen, then open a support ticket from the joystick seller.
If this does not happen, then open a support ticket from the joystick seller.
- Thu Oct 14, 2021 18:50
- Forum: Программное обеспечение
- Topic: Gladiator mkii смена осей при смене mode?
- Replies: 13
- Views: 8562
Re: Gladiator mkii смена осей при смене mode?
Возможно всё, только нужно больше данных. Какая ручка используется - с твистом или без? Скриншот из Profile-Axes покажите.
- Sat Oct 09, 2021 19:28
- Forum: Тех. поддержка
- Topic: Комп не видит джой с коробки. Blackbox индикация не горит
- Replies: 1
- Views: 2390
Re: Комп не видит джой с коробки. Blackbox индикация не горит
Причин может быть несколько, поэтому почитайте личку.
- Sat Oct 09, 2021 11:11
- Forum: Manuals and Howtos
- Topic: How to repead Button press -> Generator G8 / Show profile in config SW
- Replies: 4
- Views: 1857
Re: How to repead Button press?
It's easy to do, I'll show you step by step. 1. in the zconfig.ini file, at the bottom of the [User] section, add lines for each profile, like Profile 1 (... 255) = DCS Spitfire and close the file with saving № profile.jpg 2.after that, in the configurator, in the Global-Common tab in the Profile ID...
- Sat Oct 09, 2021 10:27
- Forum: Technical Support
- Topic: VKB Gladiator NXT Premium Firmware question
- Replies: 2
- Views: 1094
Re: VKB Gladiator NXT Premium Firmware question
In the information line of the configurator, its version (92.06) and the recommended firmware version (in brackets) are indicated. You can use a version higher than the recommended version, but not desirable below. If everything works for you, then don't worry.
- Thu Oct 07, 2021 23:21
- Forum: Technical Support
- Topic: Gladiator NXT calibration issues
- Replies: 14
- Views: 3658
Re: Gladiator NXT calibration issues
That's great, just great!
- Thu Oct 07, 2021 22:41
- Forum: Technical Support
- Topic: Gladiator NXT calibration issues
- Replies: 14
- Views: 3658
Re: Gladiator NXT calibration issues
Change the conductors in the connector according to the picture.
It should be - green, white, red, black. Only on the connector on the controller side, do not change on the sensor.
It should be - green, white, red, black. Only on the connector on the controller side, do not change on the sensor.
- Thu Oct 07, 2021 21:55
- Forum: Technical Support
- Topic: Gladiator NXT calibration issues
- Replies: 14
- Views: 3658
Re: Gladiator NXT calibration issues
The sensor cable may have been loose or damaged during magnet handling. Please check it out.
- Thu Oct 07, 2021 21:45
- Forum: Technical Support
- Topic: Gladiator NXT calibration issues
- Replies: 14
- Views: 3658
Re: Gladiator NXT calibration issues
In the Settings tab, activate the Partial Calibrations checkbox and from the pop-up window select only the 2nd axis you need for calibration.
When moving the handle, hold it a little in the extreme positions.
When moving the handle, hold it a little in the extreme positions.
- Thu Oct 07, 2021 21:25
- Forum: Technical Support
- Topic: Gladiator NXT calibration issues
- Replies: 14
- Views: 3658
Re: Gladiator NXT calibration issues
Once again, there is no need to change or configure anything. Just reset to default with the button in the configurator and then calibrate according to the above method.
- Thu Oct 07, 2021 20:56
- Forum: Technical Support
- Topic: Gladiator NXT calibration issues
- Replies: 14
- Views: 3658
Re: Gladiator NXT calibration issues
No axis has been calibrated. Do not open the Test tab, we will calibrate from this one.
Press Tools, select all axes in the window, move each axis along the full range, press End.
We show the screenshot.
Press Tools, select all axes in the window, move each axis along the full range, press End.
We show the screenshot.
- Thu Oct 07, 2021 20:39
- Forum: Technical Support
- Topic: Gladiator NXT calibration issues
- Replies: 14
- Views: 3658
Re: Gladiator NXT calibration issues
Show the Profile-Axes tab after calibration. Reset to default before it.
- Thu Oct 07, 2021 20:14
- Forum: Тех. поддержка
- Topic: Gunfighter MK II & Airbus sidestick
- Replies: 3
- Views: 5175
Re: Gunfighter MK II & Airbus sidestick
Попробуйте написать на sales@vkb-sim.pro, может помогут в приобретении. По-другому никак не получится.