Search found 1636 matches

by Victorus
Thu Jul 17, 2025 12:24
Forum: Technical Support
Topic: Random noise artifacts on 3 axis
Replies: 8
Views: 145

Re: Random noise artifacts on 3 axis

Step1. Check X axis, uncheck Y.
2. Move grip. Register outputs.
3.Check Y axis, uncheck X.
4. Move grip. Register outputs.
May be it will allow to find axis - error source.
by Victorus
Thu Jul 03, 2025 15:56
Forum: Technical Support
Topic: Gladiator NXT EVO Ministick-Toggle as always on button
Replies: 3
Views: 252

Re: Gladiator NXT EVO Ministick-Toggle as always on button

Short answer - yes. Please show screenshots of your buttons tab.
by Victorus
Fri Jun 27, 2025 23:45
Forum: Тех. поддержка
Topic: Gunfighter Mk.III ‘Modern Combat Edition’ Ultimate (CEA) Перестали работать кнопки.
Replies: 9
Views: 481

Re: Gunfighter Mk.III ‘Modern Combat Edition’ Ultimate (CEA) Перестали работать кнопки.

А что со шлейфом? Из рисунка не понятно. А так стандартный 4-х пиновый разъем.
by Victorus
Thu Jun 19, 2025 10:16
Forum: Technical Support
Topic: T-Rudder end-to-end calibration problems
Replies: 2
Views: 267

Re: T-Rudder end-to-end calibration problems

Try to set Mpl =10.
by Victorus
Sat May 31, 2025 22:40
Forum: Technical Support
Topic: A2 button (red button) not detected in NXT evo R SCG
Replies: 3
Views: 390

Re: A2 button (red button) not detected in NXT evo R SCG

Please show screenshots of your buttons settings. Phys ang Log tabs.
by Victorus
Fri May 30, 2025 9:20
Forum: Technical Support
Topic: Pedals error read CPUID issue
Replies: 14
Views: 1270

Re: Pedals error read CPUID issue

Please show you controller photo image, versions of SW, FW, bootloader, screenshots of error messages.
by Victorus
Mon May 26, 2025 14:11
Forum: Technical Support
Topic: Pedals error read CPUID issue
Replies: 14
Views: 1270

Re: Pedals error read CPUID issue

Your controller is ready to receive firmware. Launch bootloader and use it. First of all you MUST read UserGuide.
by Victorus
Mon May 05, 2025 11:14
Forum: Technical Support
Topic: Repeated button inputs on STECS and Gladiator – how to disable?
Replies: 2
Views: 997

Re: Repeated button inputs on STECS and Gladiator – how to disable?

How do you register outputs? Have you mapped joystick buttons to keyb shortcuts? What versions of SW&FW do you use?
by Victorus
Thu Apr 17, 2025 9:47
Forum: Technical Support
Topic: Gladiator NXT Joystick
Replies: 3
Views: 2389

Re: Gladiator NXT Joystick

Show screenshots of physical and logical axes parameters in vkbdevcfg.exe.
by Victorus
Tue Apr 15, 2025 14:33
Forum: General discussions
Topic: Is it possible to offset EVO axes using secondary controller?
Replies: 2
Views: 3119

Re: Is it possible to offset EVO axes using secondary controller?

What controller does a little "trim box" use?
by Victorus
Fri Mar 28, 2025 12:31
Forum: Инструкции, практические советы и рекомендации
Topic: Gunfighter в системе, которого нет...
Replies: 9
Views: 4856

Re: Gunfighter в системе, которого нет...

Разбираться в программе, искать по папкам установки симулятора. После удаления USB устройства его драйверы автоматом переустановятся, если оно подключено. Ничего страшного не случится.
by Victorus
Fri Mar 28, 2025 10:05
Forum: Инструкции, практические советы и рекомендации
Topic: Gunfighter в системе, которого нет...
Replies: 9
Views: 4856

Re: Gunfighter в системе, которого нет...

Посмотрите в инишниках ДКС. В Ил-2 накапливаются тоже несуществующие устройства. Их еще можно и в интерфейсе просмотреть.
У вас показан скриншот USBDeview. Пробовали в нем uninstall сделать?
by Victorus
Tue Mar 18, 2025 14:18
Forum: Technical Support
Topic: Bind keys to Twist (Z) axis
Replies: 7
Views: 22079

Re: Bind keys to Twist (Z) axis

NJoy32 Family Controllers Configuration Utility User guide https://disk.yandex.ru/i/gMXdc7nA6cwRgA ... 3.7. Axes2Buttons; axis rotation to button press sequence conversion ... Choose axis response range division type from Type combo box. - OFF – no conversion. - Edges1 – single button press on bound...
by Victorus
Mon Mar 17, 2025 23:05
Forum: Technical Support
Topic: GNX SEM Gear/Flaps axes issue
Replies: 4
Views: 20877

Re: GNX SEM Gear/Flaps axes issue

Look https://www.youtube.com/watch?v=moj2FOYNNe0. How to set flaps&gear levers as axes.

Go to advanced search