Search found 8 matches
- Tue Feb 28, 2023 9:39
- Forum: Technical Support
- Topic: GNX WWII Throttle Combo
- Replies: 13
- Views: 1594
Re: GNX WWII Throttle Combo
It was plugged in directly before, but I plugged it into another USB directly. The blue light still flashes. Anything else Ican try? If I have to flash it again, I think I am going to send it back. Thanks again for your help.
- Mon Feb 27, 2023 6:28
- Forum: Technical Support
- Topic: GNX WWII Throttle Combo
- Replies: 13
- Views: 1594
Re: GNX WWII Throttle Combo
Well bad news. It worked fine for a couple of sessions and then in the middle of a flight, it stopped working and the blue light started flashing and all the other LED's went off. What now? Thanks.
- Fri Feb 24, 2023 19:13
- Forum: Technical Support
- Topic: GNX WWII Throttle Combo
- Replies: 13
- Views: 1594
Re: GNX WWII Throttle Combo
OK, I must have run this process 20 times. I intended this morning to try again and get screenshots of every step of the process to send to you, but it worked! I ran MSFS 2020 and it recognized the throttle and the throttle worked on an airplane in the sim. So I will cross my fingers and hope it hol...
- Tue Feb 21, 2023 7:14
- Forum: Technical Support
- Topic: GNX WWII Throttle Combo
- Replies: 13
- Views: 1594
Re: GNX WWII Throttle Combo
In fact, if it helps any, that is how the problem started. When I received the device, it worked fine, I calibrated it, and it worked with msfs for several days, and then stopped, none of the lights lit up except the blue flashing light on the front. Now, after the reboot sequence we discussed above...
- Tue Feb 21, 2023 7:04
- Forum: Technical Support
- Topic: GNX WWII Throttle Combo
- Replies: 13
- Views: 1594
Re: GNX WWII Throttle Combo
I did all of that. It seemed to work, I calibrated, and then a couple of minutes later, before I could run msfs, it started flashing blue. MSFS didn't recognize it. Now, when I try to run the bootloader sequence again, it seems to work, but it cuts off and a purple light starts flashing on the devic...
- Sun Feb 19, 2023 22:51
- Forum: Technical Support
- Topic: GNX WWII Throttle Combo
- Replies: 13
- Views: 1594
Re: GNX WWII Throttle Combo
I get to step 5, and I get the screen VKB1 attached. Whether I double click on "VKBim NXT V2.10.8," or highlight it, when I press Start Boot I get Screen VKB2 attached ("zBoot Njoy32"). I then press ... and select the file you indicate and I get Screen VKB3 attached. I have also ...
- Sun Feb 19, 2023 8:09
- Forum: Technical Support
- Topic: GNX WWII Throttle Combo
- Replies: 13
- Views: 1594
Re: GNX WWII Throttle Combo
Screenshot attached. Thank you.
- Sun Feb 19, 2023 7:04
- Forum: Technical Support
- Topic: GNX WWII Throttle Combo
- Replies: 13
- Views: 1594
GNX WWII Throttle Combo
I purchased a GNX WWII throttle combo (GNX THQ/ GNX SEM); it worked for awhile, but the VKB software no longer recognizes it. The device shows up on the configurator as VKB Sim NXT XT V2.108, but there are no axes and no buttons work. Please help!