Search found 11 matches
- Mon Nov 08, 2021 10:04
- Forum: General discussions
- Topic: How to mount gunfighter to sim rig
- Replies: 8
- Views: 6550
Re: How to mount gunfighter to sim rig
Thank you for taking the time to answer, and also good to hear that you are happy with the purchasce. When the time comes I will absolutely consider a flight chair, but since it's only been a few months since I bought the Flight Stand (which is by no means cheap) and an Arozzi gaming chair.... well ...
- Fri Nov 05, 2021 14:36
- Forum: Manuals and Howtos
- Topic: Setting up/Assembling a new Gundifghter Mk3
- Replies: 22
- Views: 9200
Re: Setting up/Assembling a new Gundifghter Mk3
I'm in the same boat. Just purchased a Gunfighter Mk III Ultimate and am shocked at the lack of documentation/videos detailing instructions for noob initial assembly, especially since it's their top-of-the-line product. How does the joystick get attached to the extension? Is it screwed in? How does...
- Fri Nov 05, 2021 14:11
- Forum: General discussions
- Topic: How to mount gunfighter to sim rig
- Replies: 8
- Views: 6550
Re: How to mount gunfighter to sim rig
Here is my setup for comparison. For the longest time I struggled with deciding wether to buy the Monstertech flight chair or the Monstertech Fligh stand and just buying a good gaming chair. I decided for the Fligh Stand in the end... but I have to admit that Fligh Chair looks sweet. Can I ask if y...
- Fri Nov 05, 2021 13:32
- Forum: General discussions
- Topic: Thank you for some great products
- Replies: 0
- Views: 3797
Thank you for some great products
Hi, I just wanted to thank you guys at VKB for some great products. I have the VKB-SIM T-RUDDER PEDALS MK.IV and the GUNFIGHTER MK.III and both have been working flawlessy for 6 months now togheter with the Thrustmaster TWCS Throttle. I'm using a Monstertech Flight stand for it all, and thought I sh...
- Fri Jun 25, 2021 21:21
- Forum: General discussions
- Topic: Gunfighter Mk III broken wire
- Replies: 5
- Views: 2582
Re: Gunfighter Mk III broken wire
Thank you. I will of course pay the cost. Perhaps it could be something you could order from the store? Just a thought.
- Fri Jun 25, 2021 16:02
- Forum: General discussions
- Topic: Gunfighter Mk III broken wire
- Replies: 5
- Views: 2582
Re: Gunfighter Mk III broken wire
Same here, I too would like to have a spare cable lying around just in case. Where can I get one? I’m talking about the tiny cable you are suppost to disconnect when removing the gimbal to install new springs. I try to be super carefull not to put it into a position where it can be pinched, but you ...
- Thu Jun 24, 2021 17:31
- Forum: Manuals and Howtos
- Topic: Setup for new Gunfighter MK3
- Replies: 8
- Views: 6275
Re: Setup for new Gunfighter MK3
For future reference: I ended up installing extra #20 springs on each axis. I did struggle a bit to loosen the connector from the circuit-board, but once that was done installing the springs as shown in the video was quite easy. Very happy with the end result, feels much better with the extra spring...
- Tue Jun 15, 2021 21:14
- Forum: Manuals and Howtos
- Topic: Setup for new Gunfighter MK3
- Replies: 8
- Views: 6275
Re: Setup for new Gunfighter MK3
Thank you, that cleared up a lot of my questions. Have a nice week!
- Tue Jun 15, 2021 20:15
- Forum: Manuals and Howtos
- Topic: Setup for new Gunfighter MK3
- Replies: 8
- Views: 6275
Re: Setup for new Gunfighter MK3
Thank you so much for your reply fallout9, sorry for the double post. I have watched the video now, and when I feel brave enough I will try to switch springs. Will use the factory setup for a while before going full «engineer mode» though. Just a few more questions before I’ll leave you alone. Sorry...
- Tue Jun 15, 2021 18:07
- Forum: General discussions
- Topic: New (noob!) customer, advice needed.
- Replies: 9
- Views: 3454
Re: New (noob!) customer, advice needed.
Same here: nOOb that has just recieved his MK III. I am afraid to break it lol. One question: is it just plug and play after attaching stick, or is it recommended to adjust dampers (as illustrated in Quick Start guide). Anything else I need to do? I’m just using it from my desktop for now toghether ...
- Tue Jun 15, 2021 17:47
- Forum: Manuals and Howtos
- Topic: Setup for new Gunfighter MK3
- Replies: 8
- Views: 6275
Setup for new Gunfighter MK3
Hi all, I just recently recieved my new Gunfighter MK III (with MCG Pro). Fantastic stick but I am a bit overwhelmed with the setup. The Quick Start guide illustrates that I need to attach the stick and adjust the dampers by removing the dust cover. I did that and thightened the two damper screws ti...