Search found 8 matches
- Tue May 03, 2022 16:09
- Forum: Manuals and Howtos
- Topic: MCG Pro / GF MK II - Gate Cont Ministick Mouse Options Hidden
- Replies: 0
- Views: 5300
MCG Pro / GF MK II - Gate Cont Ministick Mouse Options Hidden
TL;DR I want to increase mouse sensitivity on the virtual mouse, as of right now I do not have access to speed or delay options under Global > Mouse Mode. I've finally got the ministicks behaving the way I wanted them to; GATE CONT (left MS) is using a2b to create 4 way HAT with Push (via use of TEM...
- Fri Jun 18, 2021 16:43
- Forum: Technical Support
- Topic: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
- Replies: 10
- Views: 4383
Re: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
just wanted to provide an update to this case, since I've now got it resolved thanks to VKB support. They shipped me a new connector PCB and associated wires, and after a couple tries reconnecting it (I did it wrong the first time, but support got me back on path) I now have full connection--all gre...
- Thu May 20, 2021 21:42
- Forum: Technical Support
- Topic: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
- Replies: 10
- Views: 4383
Re: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
That's interesting. I can tell you this--there is elevation on one side of the socket--the backlash appears disconnected slightly, and when I solder it, the connection from base to VKBConfig is stable. Then when the case is further reassembled, the damper screw (which definitely did raise and lower ...
- Thu May 20, 2021 17:11
- Forum: Technical Support
- Topic: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
- Replies: 10
- Views: 4383
Re: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
hmmm back at an impasse. I resoldered: IMG_0993 (Medium).JPG its not possible to install the board in reverse--one of the gimbal/cam heads is too close to install the plug. I backed out the damper screw as much as you can (it eventually hits the gunfighter top plate). Connection was good again, unti...
- Thu May 20, 2021 16:36
- Forum: Technical Support
- Topic: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
- Replies: 10
- Views: 4383
Re: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
IMG_0988 (Medium).JPG a further update--went ahead and tried to repair the connection with solder... and it worked! when I plugged the boards back together, nice solid connection light. However as I continued reinstalling components, I noticed a sort of flaw in the design/potential reason for why t...
- Thu May 20, 2021 15:56
- Forum: Technical Support
- Topic: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
- Replies: 10
- Views: 4383
Re: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
I did some further testing. I swapped out a similar cable from elsewhere on the gimbal, and the connection issue persisted; this lead me to believe it's a problem with the socket/board connection. I noticed that the socket has these small visible "L" shaped metal items at the back outside ...
- Thu May 20, 2021 8:21
- Forum: Technical Support
- Topic: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
- Replies: 10
- Views: 4383
Re: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
I have a multimeter and can do continuity testing, any suggestions on how to go about narrowing down which component is busted between the plug/receptacle or board?
- Thu May 20, 2021 2:10
- Forum: Technical Support
- Topic: VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
- Replies: 10
- Views: 4383
VKB MCG / GF Base Connector Issue - Causes intermittent failure of connection to base
1. Gunfighter Mk.II 'Modern Combat Edition' Gunfighter Model:Gunfighter Tabletop Grip: MCG PRO (direct from VKB webshop [Order #53434] (October 7, 2019)) 2. Device Firmware v2.025 (also tested with older firmware 1.94.B and issue persisted) 3. I'm not 100% which springs are currently in--I think pro...