Search found 10 matches
- Sun May 02, 2021 16:52
- Forum: General discussions
- Topic: MCG Grip keeps coming loose from Gunfighter 3 base
- Replies: 20
- Views: 10085
Re: MCG Grip keeps coming loose from Gunfighter 3 base
Thanks Tim for adding your experience. I've since upgraded to the MCG Ultimate, and have less disconnections although sometimes it still needed re-tightening. I only do a flight about once per week, so it was 3 flights or 3 weeks then I needed to re-tighten. I'll probably have to try what you mentio...
- Wed Apr 07, 2021 3:23
- Forum: Technical Support
- Topic: MCG Ultimate doesnt recognise hat switch replacement
- Replies: 4
- Views: 1999
Re: MCG Ultimate doesnt recognise hat switch replacement
In Australia, so I've messaged the AliExpress seller.
Hope they can fix it by firmware... prefer not to send the whole grip back.
Hope they can fix it by firmware... prefer not to send the whole grip back.
- Wed Apr 07, 2021 2:04
- Forum: Technical Support
- Topic: MCG Ultimate doesnt recognise hat switch replacement
- Replies: 4
- Views: 1999
Re: MCG Ultimate doesnt recognise hat switch replacement
Actually stable versions were already tried too.
I only updated to beta hoping it would fix the issue..
Unfortunately all versions of firmware I've tested have the same issue so far.
I only updated to beta hoping it would fix the issue..
Unfortunately all versions of firmware I've tested have the same issue so far.
- Tue Apr 06, 2021 7:19
- Forum: Technical Support
- Topic: MCG Ultimate doesnt recognise hat switch replacement
- Replies: 4
- Views: 1999
MCG Ultimate doesnt recognise hat switch replacement
Hi Guys, I've replaced both of my mini-sticks with hats (see photo). The top hat works fine for all 5 buttons. The left hat (Gate Cont) only triggers the centre push button. Left/right/up/down triggers no buttons. When I look at the axis test screen, the grip is sending axis signals even though its ...
- Thu Feb 04, 2021 9:38
- Forum: General discussions
- Topic: MCG Grip keeps coming loose from Gunfighter 3 base
- Replies: 20
- Views: 10085
Re: MCG Grip keeps coming loose from Gunfighter 3 base
If the grip comes loose there's an issue either with its tail or with the locking unit. Please fill up a service ticket. This was purchased through AliExpress, it looks like I can't raise a ticket with VKB since it needs to be raised against an order. I've sent a message to the VKB AliExpress store...
- Thu Feb 04, 2021 9:33
- Forum: General discussions
- Topic: MCG Grip keeps coming loose from Gunfighter 3 base
- Replies: 20
- Views: 10085
Re: MCG Grip keeps coming loose from Gunfighter 3 base
Mine also happened during calibration. I've got #50 springs, 10cm extension and Avia cams that are harder on the edge of the axis. I'm soon upgrading to 20cm extension which has me worried... Yes agree would rather see a more secure locking mechanism than just something that provides friction/force ...
- Thu Feb 04, 2021 9:31
- Forum: General discussions
- Topic: MCG Grip keeps coming loose from Gunfighter 3 base
- Replies: 20
- Views: 10085
Re: MCG Grip keeps coming loose from Gunfighter 3 base
Yeah it grips at the front where the screw/bolt thingy is, but there's nothing to stop the back from tilting up when you move the stick to the hard end of the axis. Within about 20 minutes it's moved up enough and lost contact. Did you get any result back yet? I've been busy but will raise a ticket ...
- Thu Jan 28, 2021 7:28
- Forum: General discussions
- Topic: MCG Grip keeps coming loose from Gunfighter 3 base
- Replies: 20
- Views: 10085
MCG Grip keeps coming loose from Gunfighter 3 base
Since I received my MCG grip not long ago, after about an hour of use the buttons stop registering and it's clear the connection to the base has come loose again. It happpens almost every session. Also it happened a few times during calibration as well. It seems when the stick gets pulled to the ver...
- Sat Dec 12, 2020 6:35
- Forum: Official announcements
- Topic: Unveiling the VKB TECS Throttle Control System (In Development)
- Replies: 335
- Views: 2640301
Re: Unveiling the VKB TECS Throttle Control System (In Development)
It might not be ready for pre-order yet.. That's usually only when it's got 1 month or so to go.
- Sat Sep 26, 2020 22:45
- Forum: Official announcements
- Topic: VKB GNX-THQ - Throttle Quadrant for Gladiator NXT anyone?
- Replies: 20
- Views: 40746
Re: VKB GNX-THQ - Throttle Quadrant for Gladiator NXT anyone?
Will this release same time as TECS throttle?
Or it will come first?
wondering if I should get this as a temporary throttle while waiting for TECS
Or it will come first?
wondering if I should get this as a temporary throttle while waiting for TECS