Search found 13 matches
- Sat Aug 24, 2019 4:10
- Forum: General discussions
- Topic: No 100mm Extension for Gunfighter Mk. I
- Replies: 2
- Views: 2136
Re: No 100mm Extension for Gunfighter Mk. I
I appreciate the reply! On a side note, any chance on 200mm availability for the Mk. I?
- Fri Aug 23, 2019 2:51
- Forum: General discussions
- Topic: No 100mm Extension for Gunfighter Mk. I
- Replies: 2
- Views: 2136
No 100mm Extension for Gunfighter Mk. I
I must admit, I was quite disappointed to see no Gunfighter Mk.I option for the 100mm extension. Are there any plans to release such a version? Ideally, I would like the 200mm version but I have been waiting for months with no luck.
- Wed Aug 21, 2019 3:59
- Forum: Technical Support
- Topic: VKB Gunfighter Mk. 1 Y Axis Issue
- Replies: 33
- Views: 16767
Re: VKB Gunfighter Mk. 1 Y Axis Issue
UIV wrote:Thank you. We try to send the replacement today.
Hey UIV,
Sent you some PMs regarding this. Still waiting on the board.
- Fri Aug 02, 2019 21:22
- Forum: General discussions
- Topic: Gunfighter Mk.I Extension
- Replies: 1
- Views: 1605
Gunfighter Mk.I Extension
Hi there VKB team!
I was excited to see the Mk.II extensions are available again. Any chance we can see Mk.I availability in NA anytime soon?
I was excited to see the Mk.II extensions are available again. Any chance we can see Mk.I availability in NA anytime soon?
- Fri Aug 02, 2019 21:19
- Forum: Technical Support
- Topic: VKB Gunfighter Mk. 1 Y Axis Issue
- Replies: 33
- Views: 16767
Re: VKB Gunfighter Mk. 1 Y Axis Issue
I was able to fixe the X axis issue by opening the the base and unplugging everything and plugging it back in. I'll keep an eye on it but so far so good. Y axis is still on the fritz so hopefully the replacement board takes care of that.
- Mon Jul 29, 2019 1:39
- Forum: Technical Support
- Topic: VKB Gunfighter Mk. 1 Y Axis Issue
- Replies: 33
- Views: 16767
Re: VKB Gunfighter Mk. 1 Y Axis Issue
Unfortunate update today - I have not yet received a Y axis board, but my X axis started to exhibit similar yet worse symptoms. I ran through the same battery of tests to no avail. Any help would be greatly appreciated.
- Mon Jul 22, 2019 21:41
- Forum: Technical Support
- Topic: VKB Gunfighter Mk. 1 Y Axis Issue
- Replies: 33
- Views: 16767
- Mon Jul 22, 2019 0:04
- Forum: Technical Support
- Topic: VKB Gunfighter Mk. 1 Y Axis Issue
- Replies: 33
- Views: 16767
Re: VKB Gunfighter Mk. 1 Y Axis Issue
The final step I could think of was testing the response without a spring. Here are the results. Based on this, I believe the issue to be related to the sensor.
- Sun Jul 21, 2019 3:43
- Forum: Technical Support
- Topic: VKB Gunfighter Mk. 1 Y Axis Issue
- Replies: 33
- Views: 16767
Re: VKB Gunfighter Mk. 1 Y Axis Issue
And more images.
- Sun Jul 21, 2019 3:42
- Forum: Technical Support
- Topic: VKB Gunfighter Mk. 1 Y Axis Issue
- Replies: 33
- Views: 16767
Re: VKB Gunfighter Mk. 1 Y Axis Issue
2nd Update - I dove into the hardware a bit more. No obvious issues that I can see. Copious amounts of air duster in and around what I assume to be the Mars sensor had no effect. If there are any further steps that could be helpful, I would be very grateful. I don't mind getting my hands dirty if I ...
- Sat Jul 20, 2019 6:45
- Forum: Technical Support
- Topic: VKB Gunfighter Mk. 1 Y Axis Issue
- Replies: 33
- Views: 16767
Re: VKB Gunfighter Mk. 1 Y Axis Issue
Update - I back-revved firmware to 1.96D, which had previously worked ok, and am still experiencing the bump.
- Fri Jul 19, 2019 18:13
- Forum: Technical Support
- Topic: VKB Gunfighter Mk. 1 Y Axis Issue
- Replies: 33
- Views: 16767
Re: VKB Gunfighter Mk. 1 Y Axis Issue
I have defaulted and recalibrated a few times, as well as when I swapped cams and springs. This did not seem to help.
- Fri Jul 19, 2019 7:51
- Forum: Technical Support
- Topic: VKB Gunfighter Mk. 1 Y Axis Issue
- Replies: 33
- Views: 16767
VKB Gunfighter Mk. 1 Y Axis Issue
Hi there, 1. Model - Gunfighter Mk.1/REV A w/ MCG Pro 2. Firmware - _BlackBox_GF_MCG_PRO_v1_96_F.vkb 3. Spring - Single #30 spring on each axis. 4. Cam - #30 on each axis. 5. VKB Device Config - v0.90.28 6. Joytester Screenshots - See attached. 7. Device Config Screenshots - See attached. I purchase...